background image

Warranty

14

UHF CB Transceiver

UNIDEN UH038SX-2NB

UNIDEN UH038SX-2NB UHF CB Transceiver

NOTE

Please keep your sales docket as it provides evidence for warranty.

Important:

  Evidence of original purchase is required for warranty service.

Warrantor:

  Uniden Australia Pty Limited, A.B.N. 58 001 865 498, Uniden New Zealand Limited

Warranty is only valid in the original country of purchase.
ELEMENT OF WARRANTY:

 Uniden warrants to the original retail owner for the duration of 

this warranty, its UH038SX-2NB Radio (herein after referred to as the Product), to be free from 

defects in materials and craftsmanship with only the limitations or exclusions set out below. 

WARRANTY DURATION: 

This warranty to the original retail owner only, shall terminate and 

be of no further effect ONE (1) years after the date of original retail sale. This warranty will 

be deemed invalid if the product is;

(A)  Damaged or not maintained as reasonable and necessary,

(B)  Modified, altered or used as part of any conversion kits, subassemblies, or any  

   configurations not sold by Uniden,

(C)  Improperly installed,

(D)  Repaired by someone other than an authorized Uniden Repair Agent for a defect or  

   malfunction covered by this warranty,

(E)  Used in conjunction with any equipment or parts or as part of a system not 

manufactured by Uniden, or 

(F)  Where the Serial Number label of the product has been removed or damaged beyond recognition.

Warranty only valid in the country of original retail/sale.

PARTS COVERED:

 This warranty covers for ONE (1) years, the Product and included accessories. 

STATEMENT OF REMEDY:

 In the event that the Product does not conform to this warranty 

at any time while this warranty is in effect, the warrantor at its discretion, will repair the defect 

or replace the Product and return it to you without charge for parts or service. This warranty 

does not provide for reimbursement or payment of incidental or consequential damages.
This EXPRESS WARRANTY is in addition to and does not in any way affect your 

rights under the TRADE PRACTICES ACT 1974 (Cth) (Australia) or the CONSUMER 

GUARANTEES ACT (New Zealand).

PROCEDURE FOR OBTAINING PERFORMANCE OR WARRANTY:

 In the event that the 

product does not conform to this warranty, the Product should be shipped or delivered, freight pre-

paid, with evidence of original purchase (e.g. a copy of the sales docket), to the warrantor at:

UNIDEN AUSTRALIA PTY LIMITED

Service Division

345 Princes Highway,

Rockdale, NSW 2216

Fax (02) 9599 3278

www.uniden.com.au

UNIDEN NEW ZEALAND LIMITED

Service Division 

150 Harris Road, 

East Tamaki, Auckland 2013 

Fax (09) 274 4253

www.uniden.co.nz

Summary of Contents for UH038SX-2NB

















Reviews: