background image

Operation

VOX

VOX is the automatic transmitting function by inputting voice into the 

VOX headset mic without pressing the PTT key.
1.   Press 

SELECT 

/   key momentarily twice while in

    standby mode to enter VOX Sensitivity mode. The

    current selected VOX setting will flash on the display.

2.   Press   or   key to adjust the VOX sensitivity. 1 is

    the highest sensitivity and 4 is the lowest sensitivity.

    VOX can be turned off by selecting 

OF

 icon.

3.   Press 

SELECT 

/   key five times to confirm the

    setting and exit to standby mode.
The 

VOX

 icon is shown on the display when VOX is selected to on and 

the VOX Headset is plugged into VOX Headset Jack.

The 

TX

 icon blinks when the voice level is possible to transmit at the

current selected VOX sensitivity level.

Transmitting a Call Tone

Your UH038SX-2NB radio is equipped with 5 selectable call tones that 

will be transmitted when the 

 / 

CALL 

key is pressed momentarily.

To select a call tone:

1.  Press 

SELECT 

/   key momentarily three times

 

while in standby mode to enter Call Tone mode. The

 

current call tone number (C1-C5) will be indicated.

2.  Press the   or   key to select desired call tone.

 

Each tone will be heard through the speaker.

3.  Press 

SELECT 

/   key four times to confirm and exit to standby mode.

 

To transmit the selected call tone, press the 

 / 

CALL 

key.

 

The selected tone will automatically be transmitted for a fixed length

 

of time. Call Tone will be cancelled when the 

PTT

 key is pressed.

NOTE

Current regulations require calling tones to be restricted to 

one transmission per minute. If a second transmission is 

attempted within one minute then an error tone will sound.

10

UHF CB Transceiver

UNIDEN UH038SX-2NB

Summary of Contents for UH038SX-2NB

















Reviews: