manualshive.com logo in svg

Uniden UBC355XLT, Owner'S Manual, Page: 17 / 68

Share
Download
Uniden UBC355XLT Owner'S Manual Download Page 17

17

4.  Mount the scanner to the bracket only after the wiring has 

been connected to the rear panel. 

Permanently Connecting the Mobile Power Supply

CAUTION: If you are not experienced in connecting 
accessories to the vehicle fuse box, please see your 
automotive dealer for advice on proper installation . 

1.  Check the vehicle battery connections to determine which 

battery terminal (positive or negative) is grounded to the 
engine block or chassis. Most of today’s vehicles use a 
negative ground. If your vehicle has a negative ground, follow 
Steps 2 and 3. Otherwise, skip to the Caution in Step 3. 

2.  Connect the RED wire of the DC power cord to the accessory 

contact in your vehicle’s +13.8 VDC fuse box. 

3.  Connect the BLACK wire of the DC power cord to the negative 

side of the vehicle (usually the chassis). 

Caution: In vehicles with a positive ground, the REd wire 
connects to the chassis and the blACK wire connects to 
the accessory contact in the fuse box . 

4.  Insert the DC plug into the DC 13.8V jack on the back panel. 

Summary of Contents for UBC355XLT





































































Reviews:

No comments