background image

One Year Limited Warranty

Important:

Evidence of original purchase is required for warranty service.

WARRANTOR:

UNIDEN AMERICA CORPORATION (“Uniden”)

ELEMENTS OF WARRANTY:

Uniden warrants, for one year, to the original retail owner, this

Uniden Product to be free from defects in materials and craftsmanship with only the

limitations or exclusions set out below.

WARRANTY DURATION:

This warranty to the original user shall terminate and be of no

further effect 12 months after the date of original retail sale. The warranty is invalid if the

Product is (A) damaged or not maintained as reasonable or necessary, (B) modified, altered,

or used as part of any conversion kits, subassemblies, or any configurations not sold by

Uniden, (C) improperly installed, (D) serviced or repaired by someone other than an

authorized Uniden service center for a defect or malfunction covered by this warranty, (E)

used in any conjunction with equipment or parts or as part of any system not manufactured by

Uniden, or (F) installed or programmed by anyone other than as detailed by the Operating

Guide for this product.

STATEMENT OF REMEDY:

In the event that the product does not conform to this warranty at

any time while this warranty is in effect, warrantor will repair the defect and return it to you

without charge for parts, service, or any other cost (except shipping and handling) incurred by

warrantor or its representatives in connection with the performance of this warranty. THE

LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE AND ENTIRE WARRANTY PERTAINING

TO THE PRODUCT AND IS IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY

NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR ARISING BY OPERATION OF LAW,

INCLUDING, BUT NOT LIMITED TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR

FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES NOT COVER OR PROVIDE FOR

THE REIMBURSEMENT OR PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. Some

states do not allow this exclusion or limitation of incidental or consequential damages so the

above limitation or exclusion may not apply to you.

LEGAL REMEDIES:

This warranty gives you specific legal rights, and you may also have other

rights which vary from state to state. This warranty is void outside the United States of America.

PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY

: If, after following the

instructions in this Operating Guide you are certain that the Product is defective, pack the

Product carefully (preferably in its original packaging). Include evidence of original purchase

and a note describing the defect that has caused you to return it. The Product should be

shipped freight prepaid, by traceable means, or delivered, to warrantor at:

Uniden America Corporation

4700 Amon Carter Blvd

Fort Worth, TX 76155

(800) 297-1023, 8 a.m. to 5 p.m. Central, Monday through Friday

One

Year

Limited

Warranty

Summary of Contents for EXS9005




































Reviews: