background image

34

Battery replacement
and handling

When the operating time
becomes short, even after a
battery is recharged, please
replace the battery.
With normal usage, your
battery should last about one
year.
Please contact your place of
purchase for a replacement
battery.

RECYCLING NICKEL-
CADMIUM BATTERIES

NICKEL-
CADMIUM 
BATTERIES
MUST BE
DISPOSED OF 
PROPERLY.

Nickel-cadmium cells are used
in the battery pack. Please
take your used nickel-
cadmium battery packs to a
store that recycles nickel-
cadmium batteries.

Power Failure

During the period that the
power is off, you will not
be able to make or receive
calls with the telephone.

Ni-Cd

Caution

• Use the specified battery pack.
• Do not remove the battery from the handset to charge it.
• Never throw the battery into a fire, disassemble it, or heat it.
• Do not remove or damage the battery casing.

When slightly dirty

Wipe with a soft, dry cloth.

When very dirty

Wipe with a soft cloth that has
been dampened with diluted,
neutral detergent. Dry with a
dry cloth.

When the charging
terminals become dirty

Wipe with a pencil eraser or
other contact cleaner.

Caution

Do not use paint thinner,
benzene, alcohol, or other
chemical products. Doing
so may discolor the surface
of the telephone and
damage the finish.

Note on power sources

Maintenance

EXS 9950 6th  99.9.24 5:32 PM  Page 37

Summary of Contents for EXS 9950











































Reviews: