Uniden EXP 4241 Series Owner'S Manual Download Page 8

7

Dialing a Stored Number

1) When the phone is in standby mode, press the 

talk

 key, and listen for a dial tone. 

2) Press the 

memory

 key and enter the speed dial entry (

0-9

) that has the stored number you 

want to dial. (If you enter a digit that does not contain a stored number, the handset will 

beep rapidly, and the phone will not dial.)

Chain Dialing

The speed dial memory is not limited to phone numbers. You can store any number (up to 20 

digits) that you need to enter once your call connects. This is referred to as Chain Dialing.

For example, you can save your bank account number to speed dial memory. When you call 

your bank's telephone teller service and are prompted to enter your account number, simply 

press the 

memory

 key and the speed dial number where you stored your account number.

Erasing a Stored Number from Memory

1) With the phone in standby mode, press the 

memory

 key twice.

2) Press the number of the speed dial entry. A tone indicates that the stored number is 

erased from memory.

Changing the Digital Security Code

The digital security code is an identification code used to connect the handset and the base 

unit. Normally, setting the code is not necessary.
The first time you charge your handset, the security code is automatically set. In the rare 

situation that you suspect another cordless telephone is using the same security code, you 

can change the code.
1) Remove the handset from the base unit. Press and hold the 

find handset

 key on the 

base.

2) While holding the 

find handset

 key, place the handset in the base unit. Leave the handset 

in the base for more than three seconds. A new random security code is set.

NOTE:

If the handset battery pack is completely discharged or the battery pack is removed, 

the digital security code will be lost. If this happens, a new security code is set 

automatically next time the battery pack is charged.

Operational Frequency

This cordless phone uses advanced technology which combines 2.4GHz and 900MHz for 

enhanced security and clarity.

Frequency

924.516925 – 926.704425 MHz
2,405.155942 – 2,411.718441 MHz

up050.fm  Page 7  Tuesday, October 5, 2004  4:12 PM

Summary of Contents for EXP 4241 Series













Reviews: