Uniden EXP 4241 Series Owner'S Manual Download Page 12

One Year Limited Warranty

Important:Evidence of original purchase is required for warranty 

service.

WARRANTOR: UNIDEN AMERICA CORPORATION (“Uniden”)
ELEMENTS OF WARRANTY: Uniden warrants, for one year, to the 

original retail owner, this Uniden Product to be free from defects in 
materials and craftsmanship with only the limitations or exclusions set 
out below.
WARRANTY DURATION: This warranty to the original user shall 
terminate and be of no further effect 12 months after the date of original 
retail sale. The warranty is invalid if the Product is (A) damaged or not 
maintained as reasonable or necessary, (B) modified, altered, or used 

as part of any conversion kits, subassemblies, or any configurations not 
sold by Uniden, (C) improperly installed, (D) serviced or repaired by 
someone other than an authorized Uniden service center for a defect or 
malfunction covered by this warranty, (E) used in any conjunction with 
equipment or parts or as part of any system not manufactured by 
Uniden, or (F) installed or programmed by anyone other than as 

detailed by the owner’s manual for this product.
STATEMENT OF REMEDY: In the event that the product does not 
conform to this warranty at any time while this warranty is in effect, 
warrantor will either, at its option, repair or replace the defective unit 
and return it to you without charge for parts, service, or any other cost 
(except shipping and handling) incurred by warrantor or its 

representatives in connection with the performance of this warranty. 
Warrantor, at its option, may replace the unit with a new or refurbished 
unit. THE LIMITED WARRANTY SET FORTH ABOVE IS THE SOLE 
AND ENTIRE WARRANTY PERTAINING TO THE PRODUCT AND IS 
IN LIEU OF AND EXCLUDES ALL OTHER WARRANTIES OF ANY 
NATURE WHATSOEVER, WHETHER EXPRESS, IMPLIED OR 

ARISING BY OPERATION OF LAW, INCLUDING, BUT NOT LIMITED 
TO ANY IMPLIED WARRANTIES OF MERCHANTABILITY OR 
FITNESS FOR A PARTICULAR PURPOSE. THIS WARRANTY DOES 
NOT COVER OR PROVIDE FOR THE REIMBURSEMENT OR 
PAYMENT OF INCIDENTAL OR CONSEQUENTIAL DAMAGES. 
Some states do not allow this exclusion or limitation of incidental or 

consequential damages so the above limitation or exclusion may not 
apply to you.
LEGAL REMEDIES: This warranty gives you specific legal rights, and 
you may also have other rights which vary from state to state. This 
warranty is void outside the United States of America and Canada.
PROCEDURE FOR OBTAINING PERFORMANCE OF WARRANTY: If, 

after following the instructions in the owner’s manual you are certain 
that the Product is defective, pack the Product carefully (preferably in 
its original packaging). The Product should include all parts and 
accessories originally packaged with the Product. Include evidence of 
original purchase and a note describing the defect that has caused you 
to return it. The Product should be shipped freight prepaid, by traceable 

means, to warrantor at:

Uniden America Corporation

Parts and Service Division

4700 Amon Carter Blvd. Fort Worth, TX 76155

(800) 297-1023, 8 a.m. to 5 p.m. Central, Monday through Friday

www.uniden.com

©2004 Uniden America Corporation, Fort Worth, Texas
Custom manufactured in China.

Contains additional foreign articles.
UPZZ01050BZ

up050.fm  Page 11  Tuesday, October 5, 2004  4:12 PM

Summary of Contents for EXP 4241 Series













Reviews: