manualshive.com logo in svg

Uniden EXAI4580 - EXAI 4580 Cordless Phone, Owner'S Manual

Share
Download
Uniden EXAI4580 - EXAI 4580 Cordless Phone Owner'S Manual Download Page 48

47

Talk.and.Standby.Times

With average use, your handset battery provides approximately 6 hours of talk time and approximately 7 days 

of standby time. When your handset is not being used and is left off of the base unit, the battery will gradually 

discharge. You can achieve optimum battery life and performance by returning the handset to the base unit after 

each use. If the handset is left off of the base unit, the actual talk time duration will be reduced respective to the 

amount of time the handset is off of the base unit.

Low.battery.alert

When the battery pack is very low and needs to be charged, the phone is programmed to 

eliminate functions in order to save power. If the phone is not in use, LOW BATTERY appears 

on the LCD and none of the keys will operate. During a call, LOW BATTERY flashes and 

the handset beeps. Complete your conversation as quickly as possible and return the handset to the base unit for 

charging.

Note:.Information.stored.in.the.phone's.memory.will.be.retained.for.30.minutes.after.the.battery.pack.

is.removed..This.includes.all.setup.information,.last.number.dialed,.speed.dial.memory,.and.the.CID.

list.

Even when the battery pack is not being used, it will gradually discharge over a long period of time. For optimum 

performance, be sure to return the handset to the base unit after a telephone call.

Summary of Contents for EXAI4580 - EXAI 4580 Cordless Phone

































































Reviews:

No comments

Brands by name

Popular brands

Load more brands