unicraft RFW 0,5, Operating Instructions Manual Download Page 11

Spare parts

RFW-Series | Version 1.01

11

10.2 Disposing of lubricants

Lubricant manufacturers provide disposal information 
for the lubricants used. If necessary, request product-
specific data sheets.

11 Spare parts

11.1 Spare parts orders

Spare parts are available from authorised retailers or di-
rectly from the manufacturer. The contact details have 
been listed in section 1.2 Customer service.

The following key data is required for queries or spare 
parts orders:

- Device type
- Item number
- Position number
- Year of construction
- Quantity
- Desired shipping type (post, freight, sea, air, ex-

press)

- Shipping address

Spare parts orders without the aforementioned data 
cannot be taken into account. The supplier shall deter-
mine the shipping type if no relevant data was provided.

Data on the machine type, item number and year of 
manufacture is listed on the type plate attached to the 
device.

Example

The threaded rod for the roller driver RFW 1 must be 
ordered. The threaded rod  is identified in the spare 
parts drawing with the number 7.

- Type of device:   

Roller Driver RFW 1

- Item number:       

6171701

- Position number: 

7

The order number is:    

0-6171701-07

The order number consists of the item number, the 
drawing number, the position number and one digit in 
front of the item number (0).

- Place the digit 0 in front of the item No.
- Also place the digit 0 in front of the position No. 1 

trough 9.

11.2 Spare parts drawing 

The following spare parts drawing is intended to help 
identify the necessary spare parts. To order, please 
send a copy of the list of spare parts with the marked 
components to your dealer. 

 

Fig. 8: Spare parts drawing RFW

DANGER!
Risk of injury caused by the use of incor-

rect spare parts!

The use of incorrect or faulty spare parts may cause 
risks for operating staff and damage as well as mal-
functions.
-  Exclusively genuine spare parts made by the man-

ufacturer or spare parts authorised by the manufac-
turer shall be used.

-  Always contact the manufacturer if you are unsure.

NOTE!

The manufacturer warranty shall be rendered void in 
the event of a use of unauthorised spare parts

Summary of Contents for RFW 0,5,















Reviews: