2
CONNECTIONS
POS.
COLOUR
FUNCTION
1
RED
12V
2
BLACK
GND
3
ORANGE
LIGHTS OUTPUT
4
PINK
RESISTIVE INPUT
5
BLUE
REVERSE OUTPUT
6
GREY
AUX 1 (WITH RESISTANCE 1.5k IN SERIES)
7
VIOLET
RADIO RESISTIVE OUTPUT
8
GREEN/BLACK
AUX 3 (WITH RESIST. 560 ohm TO THE GND)
9
LIGHT BLUE
AUX 4 (WITH RESIST. 3.3 k TO THE GND)
10
PINK/WHITE
AUX 5 (WITH RESIST. 1 k TO THE GND)
11
YELLOW/WHITE
HANDBRAKE OUTPUT
12
INFRARED CATHODE
13
INFRARED ANHODE
14
YELLOW/BLACK
AUX 6 (WITH RESIST. 4,7 k TO THE GND)
15
RED/BLUE
AUX 7 (WITH RESIST. 220 ohm TO GND)
16
BROWN
RADIO CODE OUTPUT
17
GREY/BLACK
GND
18
VIOLET/BLACK
K-BUS
19
GREEN
CAN H
20
WHITE
CAN L
21
BLUE/YELLOW
STK OUT
22
RED/GREY
ODOMETER
18
17
16
15
14
13
12
19
22
21
20
7
6
5
4
3
2
1
8
11
10
9
HOW TO SET THE RADIO PROFILE
On default the unit offers the first profile available that is the CLARION, the GREEN LED make’s one flashes.
With the attached table select the radio needed so verify how many flashes it must to do the LED releted to
the radio of interest.
If the radio we want to set it’s the first one just press SEEK + to confirm the selection, the LED will light on
GREEN.
To select a different radio press on the steering wheel to increase the number of flashings of the
LED or VOLUME - to decrease.
Once the radio desired is selected to confirm the choice press SEEK + on the steering wheel. the LED will light
on GREEN as confirmation.
The logic of the flashes of the LED follows this behaviour:
LED
GREEN
flash meaning= units
LED
RED
flash meaning= tens
For example 5 GREEN flashes of LED , indicate the radio in the 5th position.
2 RED flashes of the LED, indicate the radio in position 20.
1 RED flash of the LED followed by 2 GREEN flashes of the LED indicate the radio in position 12.
Once the radio of interest is selected to confirm the choice press SEEK + on the steering wheel.
The led of the unit will light GREEN.
3
CBL007UNAL22
ALPINE ADAPTER
CBL007UNBL12
BLAUPUNKT ADAPTER
CBL007UNCL12
CLARION / JVC ADAPTER
CBL007UNKE11
KENWOOD ADAPTER
CBL007UNPI12
PIONEER / SONY ADAPTER
CBL007UNPN21
PANASONIC ADAPTER
IF YOU WANT TO RE-INSTALL UNICO DUAL 1C IN A NEW VEHICLE, AFTER THE
INSTALLATION YOU MUST RESET THE UNIT AS DESCRIBED HERE BELOW
LED
BUTTON
PRESS AND KEEP
PRESSED THE BUTTON
WHEN THE LED TURNS
OFF, RELEASE THE
BUTTON
LED
BUTTON
THE LED WILL LIGHT
RED FOR FEW
SECONDS
THEN THE LED WILL LIGHT
GREEN: THE UNIT IS SET
LED
BUTTON
LED
BUTTON
ATTENTION! THE INFRARED LED AND THE ADAPTERS NOT
INCLUDED IN THE KIT ARE SUPPLIED SEPARATELY
TROUBLESHOTTING
The unit doesn’t work and the LED is off.
Verify that the power supplying wires are correctly connected .
The unit is correctly connected but the LED is off and the unit doesn’t work.
Verify the connection of the GMLAN wires .
The unit is correctly connected and the LED flashes RED quickly.
The unit can’t do the GMLAN synchronization; please, contact Paser.
The unit is correctly connected and the LED flashes RED irregularly.
Verify the connection of the GMLAN wires.
The unit is correctly connected and the LED is lighted on RED fix.
The unit has done the GMLAN synchronization but it doesn’t recognizes the vehicle;
please, contact Paser.
