background image

 

 

HP_OWER

 

27

 

14

 

OPERATING LIMITS 

14.1

 

EVAPORATOR WATER FLOW RATE 

The nominal water flow rate is referred to a ∆T equal to 5°C, between the evaporator’s inlet and outlet temperatures. The allowed 
maximum flow rate is corresponding to ∆T=3°C; higher values may cause too high pressure drops. The allowed minimum water 
flow  rate  is  corresponding  to  ∆T=8°C  (except  for  the  models  HP_OWER  60  for  which 

a  maximum  temperature  difference  of 

∆T=

6,25°C  is  allowed

).  Insufficient  values  may  cause  too  low  evaporating  temperatures  with  the  intervention  of  safety  devices 

which  would  stop  the  unit  and,  in  some  particular  cases,  the  water  can  freeze  in  the  evaporator  coil  causing  the  refrigeration 
circuit to break down. 
We enclosed below a most accurate table showing the minimum flow rates that to ensure for the plate heat exchanger for a the 
proper  operation  of  unit  according  to  the  model  (

note:

  the  water  flow  switch  is  used  for  preventing  the  freezing  sensor  from 

failure in the case of  insufficient  water  flow but  it  does not  ensure  the minimum  flow  rate required  in order the unit can work 
properly) 

Models 

HP_OWER 

60 

90 

120 

150 

Cooling capacity for reference [kW] 

5,37 

8,79 

12,23 

13,95 

Minimum  water  flow  rate  that  to  ensure 
[m3/h] 

0,74 

0,94 

1,31 

1,50 

14.2

 

AMBIENT AIR TEMPERATURE 

The  units  are  designed  and  manufactured  to  operate,  in  summer  operation,  with  the  condensate  control,  with  outdoor  air 
temperatures ranging between -10°C and 46°C. While operating as a heat pump, the  allowed range of the outdoor temperature 
goes from -15°C to 40°C as a function  of the water outlet temperature as indicated in the below table. 

     Operation limits 

Water chiller mode 

Ambient temperature 

Minimum -10°C          M46°C 

Water outlet temperature 

 M5°C           M25°C 

Heat pump mode

 

Ambient temperature  

         Minimum -15°C          M30°C 

Water outlet temperature 

M25°C         M58°C 

Heat pump mode for sanitary hot water

 

Ambient temperature with maximum water temperature 48°C 

            Minimum -15°C          M40°C 

Ambient temperature with maximum water temperature 55°C 

            Minimum -15°C          M35°C 

Water outlet temperature 

M20°C         M58°C 

Summary of Contents for HP OWER 120





































Reviews: