UNI-T utd2000 User Manual Download Page 2

Page: 2 / 65

UTD2000 Series User Manual

Preface

Dear custumer,

Thank you for choosing this UNI-T device. In order to safely and correctly use this

instrument .please read this manual thoroughly, especially the Safety Notes part. After

reading this manual, it is recommended to keep the manual at an easily accessible place,

preferably close to the device, for future reference.

Copyright and Declaration

Trademark Information

UNI-T is the registered trademark of Uni-Trend Technology (China) Co., Ltd.

Document Version

UTD2000 -20210816-V3.00

Statement



UNI-T products are protected by patent rights in China and other countries, including

issued and pending patents.



UNI-T reserves the rights to any product specification and pricing changes.



UNI-T reserves all rights. Licensed software products are properties of Uni-Trend and

its subsidiaries or suppliers, which are protected by national copyright laws and

international treaty provisions.

Information in this manual supercedes all previously published versions.

Summary of Contents for utd2000


































































Search results

Summary of Contents for utd2000

Reviews:

Related manuals for utd2000

Brands by name

Popular brands

UNI-T utd2000, User Manual

Search results

Summary of Contents for utd2000

Reviews:

Related manuals for utd2000

Brands by name

Popular brands