background image

11

MANUAL - SOLVENT RECYCLER  -  URS900SSW 

  

 

Revised 2011-07

TROUBLE SHOOTING GUIDE

Carry out each action step until a solution is found. If the recommended actions do not solve the problem 
call Uni-ram Service in North America or contact a qualifi ed Service Technician.  

Caution: Disconnect the power supply before conducting maintenance or service.

PROBLEM

CAUSE

ACTION STEPS

Unit is plugged in, power light is 
off, Display Panel is not working.

Power is not getting to 
the unit.

Reset breaker or replace fuse. If power  is 
still not getting to the unit, call a Qualifi ed 
Service Technician. Ensure that the unit is 
the only device on a circuit with suffi cient 
capacity.                                                                         

Unit is plugged in, power light is 
on, Display Panel is not working.

Power board or 
computer board not 
functioning.

Call Uni-ram Service 

Recycled liquid is not clear

1) The liquid is react-
ing chemically.

1) Run SETUP and lower the Termperature 
Set Point.  

2) The liquid fl ow path 
is dirty. One cause is 
overfi lling the distilla-
tion tank.

2) To clean the path, follow Service Pro-
cedure 2 and then recycle 3 gal of clean 
water.

Dirty water remains in Distil-
lation Tank after recycling                                                                                                                                        
 

Note:

 1/8 Gal (500 ml) of 

recycled water is expected due 
to condensation. 

1) Poor heat  transfer 
due to dirt and debris 
left in the tank.

1) Clean the tank, replace the Liner Bag, 
recycle with pure water to test. If suc-
cessfull, the problem is due to a dirty tank, 
debris left in the tank or the water is too 
contaminated. Adjust accordingly. Follow 
Operating Procedures closely. If the level 
of contamination is too high, recycle more 
often.

2) Boiling point of the 
dirty water mixture is 
above Temperature 
Set Point. 

2) Run SETUP, raise the Temperature Set 
Point and repeat the recycling operation.
The Temperature Set Point should be be-
tween 100°C and 200°C. If the boiing point 
of the mixture is above 200°C, the mixture 
cannot be recycled in this unit.

3) The Auto Shut Off 
system is shutting the 
unit off too soon.

3) Run SETUP and over-ride the auto 
SHUT-OFF. Select a time period long 
enough to fi nish recycling. The heater will 
stay on for this duration. Repeat the recy-
cling operation.

Liner Bag sticks

Turn unit on for 5 mininutes and lift out bag 
while it is still warm.

Summary of Contents for URS900SSW


















Reviews: