background image

18

MANUAL - SOLVENT RECYCLERS  -  URS1600 SERIES, URS2000 SERIES & RI 80 Rev 2019-05

Full Product Warranty

These Uni-ram products have been engineered and manufactured to high performance standards. Each 
unit has been subjected to detailed factory testing before shipment.

This product comes with a one-year full warranty from the date of purchase. Uni-ram Corporation re-
serves the right to repair or replace the unit, free of charge, to the original purchaser if a part is found to 
be defective in material or workmanship as determined by factory service personnel. The items listed 
below under “Conditions of Warranty” as consumables are not covered.

Uni-ram reserves the right to direct the customer to ship the unit collect to the Uni-ram factory or to an ap-
proved Service Center for repair using the Uni-ram Return Goods Procedure or to repair the unit on-site. 
To prevent damage in transport, the purchaser must ship the unit in the original packaging or use alter-
nate adequate packaging. All units must be shipped clean and free of solvent. 

Conditions of Warranty:
As Uni-ram Corporation has no control over the working conditions or circumstances under which the 
purchaser stores, handles or uses the product, Uni-ram makes no warranty or claim, either expressed or 
implied with respect to this product’s fi tness for any purpose or the result to be obtained from its use. This 
condition applies to the sale of all products and no representative or distributor of Uni-ram Corporation 
has the authority to waive or change these conditions.

This warranty applies only to the original purchaser and does not apply if the unit has been misused, 
overloaded, neglected, altered or used for any purpose other than those specifi ed in the operating and 
installation instructions. Deterioration due to normal wear is not covered by this warranty. Damage due to 
accident, transportation, fi re, fl oods or acts of God is also not covered. Units whose serial numbers have 
been altered or removed are not covered. The warranty is invalid if unauthorized abrasives are used in 
this unit. Unauthorized attempts at self-repair or alterations by the owner also invalidate this warranty. 
Interior or exterior fi nishes are not covered by this warranty. 

Consumable Items are not covered by this warranty.

This warranty replaces all other warranties expressed or implied by statute or otherwise.

To make a claim, call Uni-ram Service at 1-800-417-9133 and quote the serial number of the unit.

USE ONLY GENUINE UNI-RAM LINER BAGS WHICH ARE 2 MIL THICK, LIGHT BLUE IN COLOUR. 

THEY ARE SPECIALLY MANUFACTURED TO BE STRONG, HEAT RESISTANT AND CHEMICAL 

RESISTANT. 

USE OF A NON-UNI-RAM LINER BAG MAY VOID THE WARRANTY.

Summary of Contents for RI 80



















Reviews: