Qualified/Approved personnel must be used to carry out installation
Cut and prepare a 4 inch / 100 mm clearance hole for the body (16). Coat the flange of the body and the area around the
hole with 3M 4200FC sealant then slide the body into the hole. From the inside fit the compensating ring (17) and screw
the securing ring (18) up “hand tight”. Adjust the screws (19) so the compensating ring is flush to the hull and check the
sealant has flowed completely around the flange. Do “NOT” over tighten the screws as this will squeeze the sealant from
the surface. Allow the sealant to solidify and remove surplus. Finally tighten the adjustment bolts to 4Nm / 3ft.lbs
Note for cored hulls - After cutting, the exposed surfaces of the hole must be finished to form a solid surface
through it, thus protecting the internal core of the hull.
Maximum hull thickness should not exceed 4.75 inches - 120mm Minimum wall thickness 0.375inches.- 10mm
After completing the installation procedure it is highly recmmended to coat the exposed body with antifouling.
EARTHING LIGHT FOR CATHODIC PROTECTION-tighten the earth screw on the securing ring so that it
bites into the screwed barrel. Check there is continuity to the front face. This prevents galvanic corrosion.
ORDERING NUMBERS
250 WATT LIGHTS - 230V. S00475-SA-V2W1.
150 WATT LIGHTS - 120V. S00475-SA-V3W2. 230V. S00475-SA-V2W2
UL Ti MATE 130 SA INSTALLATION
(The UL Ti MATE 130 SA should be no less than 250mm/10” below the water line
)
LENS FITTING INSTRUCTIONS
Check the glass landing surface is clean and apply a suitable silicone grease to the gaskets.
Fit the glass, gaskets and retaining ring as shown above. Hand tighten the screws with an
Allen key making sure the glass retaining ring is square. Torque the screws to 6 Nm (4.5ft/lbs)
in the sequence shown, check the ring again and re-torque the screws again to the same setting
ELECTRONIC BALLAST COMPLETE
WITH IP65 ENCLOSURE
PLEASE REGISTER YOUR PRODUCT WARRANTY DIRECT TO
WWW,REGISTER-UWL.COM
FOR TECHNICAL INFORMATION PLEASE EMAIL
SALES, PRODUCT INFORMATION AND NEWS GO TO
WWW,UNDERWATERLIGHTS.COM
UL Ti MATE 130 SA -20-8-2012
Recommended Spares
Part No
Lamp ( 250w = W1 )
91209
Lamp ( 150w = W2 )
91210
Glass with gaskets
S00281-A
Ballast
S00801
TM
OPERATIONAL CONDITIONS AND CONSIDERATIONS
The UL Ti MATE 130 is serviced from inside the hull. Allow a minimum of 170mm behind the cable gland for lamp
replacements.
ELECTRICAL INFORMATION
CABLE SPECIFICATION TO PROJECTOR
150 Watt-250 Watt-
High temp silicone three core part number. S00111-0.75-
150 WATT
Max distance between ballast and projector with -10 meters.
250 WATT
Max distance 25 meters
.Ballast power 150 watt ballast
120
/230 volt, running current
1.4
/0.7.A
Ballast power 250 watt ballast 230 volt, running current 1.2.A
Ballast will not ignite a hot lamp. The ballast has three attempts to ignite
the lamp then will wait for four minutes before repeating the cycle.
Do not attempt to remove the glass lens while afloat
UL Ti MATE 130 SA
‘submersible through hull light’
150 watt
Part Description
130-S A
Part No
1: Projector lid securing plate
00283-B
2: M6 Nut
93381
3: 'O' Ring
00108
4: Gasket NAF
00285-A
5: Connecting ring
00274-C
6: Lamp holder screw
00290
7: Lamp holder (250W)
91195
7: Lamp holder (150W)
91191
8: Reflector collar bush
00288-A
9: M4 Lock nut
93374
10: Lamp (250W)
91209
10: Lamp (150W)
91210
11: Reflector adjustment rod
00284-2-D
12: Reflector complete
S91791
13: Glass retaining ring
00476-B
13A: Cap head screws
93325
14: Glass gaskets NAF
00286-A
16: Body
S00475-A
17: Compensating ring
00277
18: Securing ring
00275
19: Cap head screws
93610
20: Ignitor (250W)
S95325
21: Projector cover (250W)
00102-H
22: Gland
00107
23: Projector cover (150W)
00102-E
24: Ballast 250 watt
S00800-V1W2
24: Ballast 150 watt 230v
S00800-V2W2
24: Ballast 150 watt 120v
S00800V3W2
EARTH TAB AND SCREW
250 watt
