manualshive.com logo in svg

UMA Solar HC-10.5, Installation Manual, Page: 25 / 35

Share
Download
UMA Solar HC-10.5 Installation Manual Download Page 25

9.

Once you are satisfied with the plumbing arrangement, go back and cement together all the joints that you have not 

already cemented. Use good plumbing techniques and rags to protect the existing pool equipment. 

NOTE:

 

Use pipe clamps the same size as the outside diameter of your plumbing fittings to secure the pipe and 

fittings tightly to the wall.

13. Connecting the Feed & Return 

Lines to the Filtration System. 

- Cont.

NOTE:

 

W

hen cementing check valves, try to do so in a horizontal position to prevent cement from dripping into the 

spring loaded valve and cementing it closed! When this is not possible, use cement sparingly and allow it to dry 

slightly before inserting the pipe into the socket. When cementing to a 3-way valve, either remove the diverter from 

the valve or cement with the diverter turned away from any open port to prevent the cement from running onto the 

diverter cementing it in place!

For a truly professional looking installation, take time to clean the white PVC pipe. Use a clean rag, pour PVC cleaner on 

it, and then wipe the dirt and identification marks off the pipe. Do this on all exposed pipe. This is also good preparation 

if you plan on painting the pipe to match the house color.

IF YOU ARE INSTALLING AN AUTOMATIC SYSTEM: 

The basic difference between the manual system just outlined and 

an automatic system is the use of a motorized 3-way valve. This 3-way valve is operated by a differential control which 

uses sensors to determine if the solar system is warmer or cooler than the pool water. This way, it can shut the solar system 

off when cloudy conditions exist and thereby generate the optimum performance from the solar investment. It also 

allows you to select a maximum pool water temperature so the solar system doesn’t overheat the pool. It accomplishes 

this by the use of a sensor on the roof and a sensor installed into the pool plumbing. The directions included with the 

automatic system components will direct you in the installation of the control and sensors. The 3-way valve will be 

installed as described in above procedure. 

 

-

 

24

CONNECTING THE FEED & RETURN LINES TO THE FILTRATION SYSTEM.

INSTALLATION MANUAL HELIOCOL

®

 SOLAR POOL HEATER

©

2014 UMA Solar

Summary of Contents for HC-10.5




































Reviews:

No comments