background image

01 

 

Before Using the Equipment 

Thank you for purchasing this product. Your custom is very much appreciated. 
This pump is designed solely for vacuum discharge, and may malfunction or cause accidents if not 
handled appropriately. Read the manual thoroughly, and pay due attention to inspections, 
maintenance, and safety. 

 

 

Personnel Handling the Equipment 

Only persons who have read this manual thoroughly, and have sufficient understanding of 
safety, pump specifications, and method of operation, may operate this pump. 

 

Read the Manual Thoroughly 

Read the manual thoroughly in order to use the equipment correctly. Read the section on 
Safe Use particularly closely. 

 

Keep This Manual in a Safe Place 

After reading this manual, be sure to keep it in a safe place which is readily accessible to 
others needing to use it. 

 

Copying This Manual Is Prohibited 

No part of this manual may be copied for use by a third party without the express 
permission of the manufacturer. 

 

Statutory Requirements for Disposal 

Follow all statutory and local authority regulations when disposing of this pump. 

 

Safety During Repair 

Please provide a full description of the circumstances of use (particularly the use of 
dangerous materials) for the safety of repair personnel when requesting the manufacturer 
for repairs to the pump. Your request for repair of may be refused if these circumstances 
are unclear. 

 

Summary of Contents for DTC-41C





























Reviews: