ultraPLAY Discovery Centers DC-2MD Assembly Instructions Manual Download Page 25

Page: 25 / 80

UltraPlay Play Systems

800.458.5872 • www.ultraplay.com

FOOTING DETAIL - CONCRETE ANCHORS

GROUND

LowerPost

CONCRETE

Extension Footer

Lock Nut

Flat Washer

(2) Concrete Anchors
(Part # 33-11-0706)

2”
Extension
Footer

2-1/2”” Rubber
Tiles

Instructions:

1. With Extension Footer in position,

mark hole position. Remove

Extension Footer and drill

(2) 3/8” Dia. x 2” deep holes

into concrete to receive anchor.

2. Insert Concrete Anchors and secure

with Flat Washer and Lock Nut.

IMPORTANT:

Never install play equipment over hard, unresilient

surfaces such as asphalt, concrete or compacted earth. It is the
owner’s responsibility to ensure the “minimum area required”
contains an appropriate amount of resilient material to cushion
accidental falls.

4” Minimum
w/ 3000 PSI

SITE PREPARATION

Clear area of any debris and level surface.
Equipment is designed to be installed on
a level surface.

Summary of Contents for Discovery Centers DC-2MD

















































































Search results

Summary of Contents for Discovery Centers DC-2MD

Reviews:

Related manuals for Discovery Centers DC-2MD

Brands by name

Popular brands

ultraPLAY Discovery Centers DC-2MD, Assembly Instructions Manual

Search results

Summary of Contents for Discovery Centers DC-2MD

Reviews:

Related manuals for Discovery Centers DC-2MD

Brands by name

Popular brands