background image

 
Brown             (+) Siren Output                Positive output for siren*
Pink                Channel 4 Output             

Programmable - See menu 2**

Wht/Blue

        

Channel 5 Output             

Programmable - See menu 2***

Red                 Main Power Input             Constant 12 Volt input
Black              Ground Input                    System ground input
Grey               (-) Trunk Release               Negative trunk release. 500ma****
White              (+) Park lights                   Programmable - 10amp Maximum 
Orange           (-) When Armed                 Negative output when system is armed****
Blk/White       (-) Dome Light                   Dome light supervision****
Purple             (+) Door Input                   Positive door pin switch input
Green             (-) Door Input                     Negative door pin switch input
Blue                (-) Hood Input                    Negative input from hood pin switch
Yellow             Ignition Input                    Input from vehicles ignition wire

Green

            

Door Lock

                        

Programmable - menu 1, setting 3.

Red                  12 Volt Output                 Output for voltage inverter only*****
Blue                 Door Unlock  

                  

Programmable - menu 1, setting 3.

Pink                 Second Unlock  

              

Programmable - menu 1, setting 3******

4 Pin Connector Red

4 Pin Connector Blue

4 Pin Connector White

This connector is for the RF antenna. The antenna also contains 2 LEDs and the 
Program Button.

Blue                Sensor Full Warn            Input trigger for addition alarm sensor(s)
Green             Sensor Pre Warn             Input trigger for addition alarm sensor(s)
Black              Ground Output               Ground output for addition alarm sensor(s)
Red                 12 Volt Output                12 volt output for additional alarm sensor(s)

* This output is designed to operate one siren. If more than one is being added, a relay 
must be installed to avoid damaging the module.
**Channel 4 is activated by holding the Star button on the transmitter.
*** Channel 5 must be programmed to activate on the # button. This channel works on
 the horn output, if the 5th channel is programmed the horn output will function as 
5th Channel.
****500ma outputs are low current and are designed to activate relays.
*****This is a low current 12volt output designed for use with a voltage inverter. 
******This output will activate on the second press of  unlock within 3 seconds.

14 Pin Connector

PAGE  5

SECURITY SYSTEM

INSTALL GUIDE

2 Pin Connector (Brown wire with female connectors)

Starter Disable harness. See page 4 for installation instructions

Summary of Contents for 660 Series













Reviews: