background image

INSTALLATION GUIDE

OPERATIONS

OPERATIONS

Remote Start

Remote Stop

Idle Mode

Turbo Timer Mode

Timer Mode

Self Learning Shock Sensor

1.Press and release the      button. 
2.The park lights will flash and the siren will chirp once.
3.When the  vehicle has started, the system will  flash the park lights four times and then 
remain “On” while the vehicle is running.  
4. The vehicle will continue to run for the programmed runtime. (normally 15 minutes).  
EXTEND RUNTIME
1.Press and release the    

 

button while the vehicle is remote started.

2.The system will respond with one park light flash and one siren chirp  to confirm Extended 
Runtime. The system will reset the run time, (normally 15 minutes).

1.Press and hold the       button for three  seconds. The remote starter will shut down.
2.The park lights will flash two  times and the siren will chirp  two times.

Note: Pressing the brake pedal or opening hood will also stop the vehicle.

1.While the vehicle is running with key, press  the        button. 
2.The park lights will turn on and the siren will chirp once.
3.Turn the ignition key “Off” and the vehicle will continue to run.
4.  Exit the vehicle and leave it running safely without the keys in the ignition.  Lock the door while the 
vehicle is left running.

1.While the vehicle is running with key, press  the # button. 
2.The park lights will turn on and the siren will chirp once.
3.Turn the ignition key “Off” and the vehicle will continue to run for 2 minutes

1.Press and release  the 

#

 

button, then press and hold the      button for six seconds, until

   The parking lights turn “On”. 
2.While the  parking lights are “on” the start cycle  can be selected.
1 hour cycle                       Press   LOCK      button                 1 Park Light Flash                             
2 hour cycle                       Press   UNLOCK button                 2 Park Light Flashes
3 hour cycle                       Press                   button                 3 flashes
4 hour cycle                       Press                   button                 4 flashes
3.System will start vehicle at selected cycle for up to 24 hours.

To Cancel Timer Mode:

1.Press and release  the 

#

 

button, then press and hold the      button for four seconds.

2.The park lights will flash and the siren will chirp twice.
3. Starting the vehicle with the key or by the remote will also cancel Timer Mode. 

#

Press the lock button 5 times, once every half second or until the siren chirps 3 times and
the park lights turn. Strike the vehicle with the amount of force wanted to trigger the alarm.
Strike the vehicle 3 times to set the impact level. Each time the vehicle is impacted the 
siren will chip. Press the unlock button to exit Shock Sensor Learning.

Reservation Mode (Manual Transmissions Only)

1. With the vehicle running, apply the park brake then press and release the brake pedal.  
2. The park lights will flash and the siren will chirp to confirm that reservation mode has been activated.
3. Remove the key from Ignition, and exit the vehicle. (the vehicle will remain running) 
4. Close the door and the vehicle will shut off.*
*If the vehicle has a delay dome-light, the vehicle may run until the dome-light turns off.
5.  The vehicle is now in Reservation Mode and may be remote started.

Note: Opening a door after this point will cancel Reservation Mode. 

1.Press and release the 

LOCK 

button. The siren will chirp once.

2.Within 3 seconds press and release the     Button the siren will chirp once.
*This feature can be used in bad weather or in areas with high levels of noise (Airports....)
Note: The shock sensor will reset the next time the alarm is armed. 

Temporary Sensor Bypass

1st

2nd-6 sec.

3 sec.

While

running

Press &

Release

While

running

Press 5

Times

2nd

1st

Summary of Contents for 2250 Series

















Reviews: