background image

ACTIVATING  SERVICE  MODE

1.

While the ignition is “ON”  press and hold the Program  Button for five seconds. The park lights will 

flash and the siren will chirp five times to confirm that the system is in Service  Mode. 

2.

 While in Service Mode the remote start functions will be disabled and LED’s will be “ON” steady.  Door 

locks and trunk release are still operational.

DEACTIVATING SERVICE MODE

1. While the ignition is “ON”  press and hold the Program  Button for five seconds. The park lights will flash 

and the siren will chirp    two  times to confirm that the system has exited  Service   Mode.  

2. Remote start functions will return to normal operation.

System Service  Mode

Service Mode- By Remote

SERVICE MODE ACTIVATED

1 - Press and release button 4 (

# Button

)

2 - Press and hold Button 4 (

# Button

) for 6 seconds until Status LED comes on Steady

Note: The siren will chirp 5 times to confirm Service Mode was entered.

SERVICE MODE DEACTIVATED

1 - Press and release Button 4 (

# Button

)

2 - Press and hold Button 4 (

# Button

) for 6 seconds until Status LED turns off.

Note: The siren will chirp 2 times to confirm Service Mode was exited.

Note: The remote starter will flash the park lights 3 times if the start button is pressed when the 
vehicle is in Service Mode.  

OPERATIONS

OPERATIONS

INSTALLATION GUIDE

LIMITED LIFETIME WARRANTY 

Limited Lifetime Warranty

  - 

Available with Professional Installation Only

The manufacturer warrants to the original purchaser of their remote starters and alarms, that the product shall be free from defects in material and workmanship. 
However, should this product be proven to be defective, within a three year period from the original date of purchase, the manufacturer will, without charge to the 
purchaser (excluding any charges incurred to have the product delivered to the manufacturer) , repair or replace any part of the remote starter and/or alarm which 
the manufacturer agrees to be defective.  After the initial three-year period a labour charge of no greater than $20.00 will apply to all defective goods.  A $20.00 
check must accompany any goods being returned to the manufacturer.  All warranties apply on to the original purchaser and the vehicle in which it is originally 
installed. Repairs or replacement of defective modules shall remain at the discretion of the manufacturer. All other parts, components, accessories and/or optional 
equipment pertaining to the remote starter and alarm are not included in the manufacturer's  warranty. This warranty is non-transferable. Request for warranty 
service from any Factory Authorized Dealer must be accompanied with the original purchase receipt or have product registered by authorized dealer on 
manufacturer's website.  Failure to comply with any of these conditions may result in warranty being voided.  If unit in not installed by an Authorized Dealer warranty 
term is limited to 15 day from date of purchase and covers manufacturing defects ONLY.  Only freight pre-paid shipments will be accepted for warranty,

This warranty does not cover the following: removal and reinstall labor charges, shipping charges, abuse, misuse, or accidental damages to the remote starter and 
alarm, automobile, and/or parts there of. This warranty is void upon modification, repairs, or alterations of any part of the System. The manufacturer does not 
guarantee or insure against theft of the vehicle or its contents. Alarm models are designed only to act as a deterrent against possible theft. This alarm may qualify 
for auto insurance discounts; contact your Insurance Agent for further information. The manufacturer shall not be held liable for any consequential damages due to 
breach of this or any other warranty, expressed, or implied.  This warranty gives you specific legal rights. Your specific legal rights may vary for each region.

CERTAIN DAMAGES EXCLUDED

  - The manufacturer expressly disclaims any liability or responsibility for incidental damages caused by the product, including 

economic loss, loss of use of the product, car rentals, or any other costs relating to the care and custody of the product. The manufacturer disclaims liability or 
responsibility for any consequential damages caused by the product or resulting from its use, including the cost of repairing or replacing other property damaged by 
the product or caused by its use, whether or not the product is working properly. The product is intended to deter unauthorized use of the vehicles in which it is 
installed.  The manufacturer does not warrant that the product is fool-safe against theft and/or vandalism and/or human error or misuse.  The manufacturer accepts 
no liability or responsibility for any damage of any kind whatsoever caused to any vehicle in which the product is installed or any resulting damage from its use.  The 
manufacturer accepts no responsibility or liability for any damage resulting to or theft of the vehicle or its contents.

Summary of Contents for 2250 Series

















Reviews: