Ultra electronics HyperSpike LineWave Series Installation And Maintenance Manual Download | Manualshive

Page: 14 / 26

background image

HyperSpike

®

LineWave Installation and Maintenance Manual

Copyright © Ultra Electronics

– USSI, Columbia City, IN 46725 USA

90243A-MAN-LINEWAVE Rev C

Page 10

2.7. 72544B-801

– Wall Mounting Kit Installation:

Reference the following instructions to install a LineWave 90243A-801 or 90243A-802 on a
wall surface:

1. Fasten two L Brackets (Part B) to the wall surface using appropriate fasteners for the wall.

Always follow local codes and safety practices.

Wall fasteners are not included in the

mounting kit.

a. 90243A-803 - L Bracket

recommended spacing is 20” apart.

b. 90243A-804 - L Bracket r

ecommended spacing is 43” apart.

Figure 8. 90243A-803 and 90243A-804 Wall Mounting

– Step 1

«
...
12
13
14
15
16
...
»

Summary of Contents for HyperSpike LineWave Series



























Reviews:

No comments

Related manuals for HyperSpike LineWave Series

Brand: JBL Pages: 2

Brand: JBL Pages: 2

Brand: JBL Pages: 2

Brand: Hamilton/Buhl Pages: 4

Brand: Piega Pages: 2

Brand: Waterfall Audio Pages: 2

Brand: T+A Elektroakustik Pages: 30

Brand: Conquer Pages: 2

Brand: Turbosound Pages: 8

Brand: Vingtor Stentofon Pages: 2

Brand: CyberData Pages: 2

MEGABOOM REMIX 2

Brand: Ultimate Ears Pages: 4

Brand: Kicker Pages: 12

PG533 HouseParty Rise 2 Wireless

Brand: Gear4 Pages: 24

Brand: X-mini Pages: 2

Control Control 28

Brand: JBL Pages: 4

Brand: Cambridge Audio Pages: 8

Brand: Masterbuilt Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands