manualshive.com logo in svg

Ultra-Aire SD12, Installation Instructions Manual

Share
Download
Ultra-Aire SD12 Installation Instructions Manual Download Page 22

22

23

Ultra-Aire SD12 Installation Instructions

www.Ultra-Aire.com | (800) 533-7533

www.Ultra-Aire.com | (800) 533-7533

Ultra-Aire SD12 Installation Instructions

DUCTING TO HVAC SYSTEMS

Alternative HVAC System Installations

If the Recommended Dedicated Ultra-Aire Return to HVAC Supply Installation is not possible, there are several 
alternative installation options available.
•  DO  NOT locate return in a bathroom or kitchen.
•  Control should be located remotely from the dehumidifier and placed in a central location.   

Dedicated Ultra-Aire Return to HVAC Return

Outdoor

Condensing

Unit

Air Handler

HVAC Supply

Dedicated Ultra-Aire 90 Return to A/C Retur

n

HVAC

Return

Fresh Air Intake 

(Optional)

Motorized

Damper

Indoor

Air Return

Ultra-Aire

Supply

Create a separate return for the Ultra-Aire 
SD12 in a central area of the building.
 Installing the supply air from the Ultra-Aire 
SD12 in the return of the HVAC system 
requires the HVAC fan to run when the 
Ultra-Aire SD12 is operating.

HVAC Return to HVAC Supply

Outdoor

Condensing

Unit

A/C Return to A/C Supply

Air Handler

HVAC Supply

HVAC

Return

Backdraft

Damper

Optional Check Damper

(no HVAC fan needed)

Fresh Air

Intake 

(Optional)

Motorized

Damper

Ultra-Aire Supply

Check Damper should be in place between 
the Return and Supply connections of the 
dehumidifier.
If Check Damper is not in place, the HVAC  
fan must turn on when the dehumidifier  
is in operation.

HVAC Return to HVAC Return

Air Handler

HVAC

Supply

A/C Return to A/C Return

HVAC Return

Fresh Air

Intake

(Optional)

Motorized

Damper

Optional Check Damper

(no HVAC fan needed)

Ultra-Aire

Supply

Outdoor

Condensing

Unit

 Check Damper should be in place between 
the Return and Supply connections of the 
dehumidifier.
 If Check Damper is not in place, the HVAC 
fan must turn on when the dehumidifier is 
in operation.

Summary of Contents for SD12





































Reviews:

No comments

Brands by name

Popular brands

Load more brands