GB/IE/NI 5
Car seat cover set
• Introduction
We congratulate you on your purchase. You have chosen a high quality product.
The instructions for use are to be considered as part of this product. Before using the
product, please familiarise yourself with all the safety information and instructions
for use. Only use the product as instructed and only for the stated areas of use. If you pass the
product on to anyone else, please ensure that you also pass on all the documentation with it.
• Intended use
Set of car seat covers for the driver‘s seat, passenger‘s seat and the back seats of cars
(according to the enclosed type list).
• Safety instructions
Correct installation res. fastening of the seat covers to the vehicle is essential to guarantee the sa-
fety of the user. Please pay attention to the following information when installing the seat covers:
•
WARNING!
DANGER OF SUFFOCATION!
Keep the pa-
ckaging out of reach of small children.
• Installation is permissible only in cars that are indicated in the list of types on the pa-
ckaging or in the enclosed, detailed list of types.
• Correct assignment of the seat (driver and front passenger seat). The covers are assig-
ned by the marking „airbag“ attached to the seat cover. This marking must be attached
to the outer side of the backrest (see fig. 1.0).
• Headrest inserts, adjustment levers / wheels for release of backrests or armrests may
not be covered with the seat cover. Allowances must be made for appropriate inserts.
Please observe the instructions given in section “Installation”.
• Displaced seat covers must be repositioned. If this is no longer possible due to a advan-
ced state of wear and tear, the cover must be removed or replaced.
• Manipulation of the opening of the seat covers is not permissible (no covering, sewing
up or repairs by yourself).
This protective cover has been tested by TÜV Rhineland Group.
CAUTION!
If the seat covers are installed incorrectly, the proper extension and infla-
tion of the seat air bag cannot be guaranteed in the case of a collision.
• Installation of seat covers
You need a pair of pointed scissors.
Important:
Please read the information below before installing the seat covers!
Fig. 1:
Remove headrests (in some car models the headrests must be dismantled in
a garage).
Fig. 2:
Cover the backrest by pulling the cover downwards.
Fig. 3:
Pay attention to the correct assignment of the side airbag label (right / left
seat)! The side airbag label must be located at the outside (door side) of the
respective seat.
Fig. 4:
Pull the strap through between the seat and the backrest.
Fig. 5:
Then close the fastener.
Fig. 6:
Cover the seat from the front to the back.
Fig. 7:
Fasten the metal hooks to the rubber loops.
Fig. 8+9:
Pull the rear rubber loops between the seat and backrest (as you did with the
strap of the backrest cover). Fasten the metal hooks under the seat according
to the car model (e.g. to the existing metal rods - ATTENTION Do not fasten
to airbag cables!)
Fig. 10:
Or fasten all rubber loops together.
ATTENTION!
Openings for backrest releases, adjustment levers etc. (as described under fig. 11–15)
must be cut out.
If your seat is equipped with armrests, proceed as described under fig.
11. Otherwise go to fig. 15.
Fig. 11:
Pull the cover down as far as the armrest. The cover must be tightly fitting on top.
Fig 12:
Cut the cover in the position of the armrest. The cut-out may not be too large.
Fig. 13:
Push up the armrest and pull it through the cut-out opening of the cover.
Fig. 14:
Pull the strap through between the seat and the backrest and close with the fastener.
If your seat is equipped with side levers, proceed as described under fig.
15. Otherwise go to fig. 19.
Fig. 15:
Open the zip fastener, upwards or downwards, at the position of the side
lever.
Fig. 16:
Expose the side lever completely and pull the zip fastener closed accordingly.
If your seat is equipped with seat frame cladding, proceed as described
under fig. 17. Otherwise go to fig. 19.
Fig. 17:
(for Renault and Mercedes) Open the seat frame cladding under the seat.
Fold the seat frame cladding under the seat cover.
Fig. 18:
Pull the strap through between the seat and the backrest. Then close the
fastener at the back.
Fig. 19:
Cover the headrests.
Fig. 20:
Open the zip fastener on the upper side of the backrest cover sufficiently so
that the mounting holes for the headrest are exposed.
Fig. 21:
Mount the front seat headrest and check the cover is correctly and tightly fitted.
Fig. 22+23:
Pull the cover for the back seat towards the back of the seat. If necessary,
tilt the back seat forward and fasten the rubber loops at the back to the
metal hooks (according to the car model).
Fig. 24:
Position the cover exactly in the location of the seat belt.
Fig. 25:
Carefully cut the cover in the position of the seat belt.
Fig. 26:
Push the cover under the seat belt holder. Pull the cover under the backrest.
The cover must be under the seat belt!
Fig. 27:
Cut the cover in the position of the belt guide.
Fig. 28:
Push the cover beneath the plastic of the belt guide.
Fig. 36:
The backrest cover is universally suitable for all back seats due to the triple zip
fastener division. The zip-in part can be used according to the width of the rear
backrest. In case of divided back seats, open the variable zip fasteners with
the slider facing upwards if necessary.
Fig. 29:
Fasten the rubber loops at the back to the metal hooks.
If your your back seat is equipped with armrests, proceed as described
under fig. 30. Otherwise go to fig. 31.
Fig. 30:
Open the zip fasteners. Fold out the armrest. Close the zip fastener up to
the armrest.
Fig. 31:
Cover the rear headrests.
Fig. 32:
Cut the backrest cover in the position of the headrest in an x-shaped form.
Fig. 33+34:
Push the cover under the plastic.
• Instructions for care and disposal
Wash the covers by hand
Do not iron
Do not use bleach
Do not dry clean
Do not dry in a tumbler
The seat covers can be disposed of in the household waste.
Please dispose of the packaging in accordance with the local regulations.
• Service & guarantee
This product has been produced with great care and under continuous quality control. The
product comes with a three year guarantee from date of purchase. Please keep your receipt
safe. The guarantee applies only to material and manufacturing defects and does not ap-
ply to misuse or improper treatment. Your statutory rights, especially the rights of warranty,
are not restricted by this guarantee.
Extent of validity: Please use the service hotline which has been provided for you or contact
the service centre in the European Economic Area.
Costs: Repair or replacement free of charge or a refund of the purchase cost. Shipping
costs will not be charged.
Advisory notice:
Before returning your product, contact our hotline by telephone, so
that we can help you with any operating errors.
Service address:
Return address:
Walser Industrie- und Handels GmbH
Walser Customer Service Germany
Walser GmbH
www.walsergroup.com
Bleicheweg 15, Postfach 3325
Service Hotline: 00800 00300030
DE-88131 Lindau
GERMANY
IAN 292911
Fig. 1.0
