background image

MSR112 Programmer’s Manual                                                             UDN PM019 Rev. A 
Section 3 -- Technical Specification                                                                                                                                      2002/5/23

 

                                                                                                                                                                                                     

Page 

13

 

Uniform Industrial Corp.

 Proprietary and Confidential            

                                                                        Total 18 pages

 

Stop Bit 

One

 

 
 

 

Transmission Format

 

 

Data output format 

Single track  <STX><SS>< TRACK 1or 2or 3 DATA><ES><ETX> 

<STX><SS>< TRACK 1 or TRACK 2 DATA><ES><DLE> 

Dual track 

<SS><TRACK 2 or TRACK 3 DATA><ES><ETX> 

Triple track 

<STX><SS><TRACK 1 DATA><ES><DLE><SS><TRACK 2 DATA><ES> 

<DLE><SS><TRACK 3 DATA><ES><ETX> 

Remarks: 

SS = START SENTINEL   

 

TRACK1=  “%”  (ISO, DMV & AAMVA) 

TRACK2=  “;”  (ISO, DMV & AAMVA) 

TRACK3=  “

;

”  (ISO)  

  “%” (AAMVA)  

“!” (CA old DMV) 

Note: TK3 SS can be replaced to + for ISO, # for AAMVA, and ! for CA old DMV while SS is enable.   

ES = END SENTINEL    

TRACK1, 2 & 3=    “?”     

(ISO, CA old DMV & AAMVA) 

 

Note: 1. If read error, the default output data format is <STX><SS>E<ES><ETX> and it can be replaced as either 

<STX><SS>F<ES><ETX> or output nothing. 

2. If no data is read, then display <STX><SS>N<ES><ETX> as default and it can be replaced as output 

nothing. 

3. <STX>, <ETX>, <DLE>, SS (start sentinel), ES (end sentinel) and LRC are optional.   

The <DLE> is programmable by command setting. 

                  4. The SS, ES or LRC are optional for each track. 

Summary of Contents for MSR112 Series



















Reviews: