background image

INSTALLATION

13

UFO

 

LIGHTING

MOUNTING

 

THE

 

ENCLOSURE

The diagram below shows the mounting hole positions on the rear face of the enclosure. 
 
Mount as follows: 
 
1. Support the enclosure against the mounting surface and use a spirit level to ensure 
that it is level. As detailed opposite, the glands must be facing downwards. 
 
2. Mark the 4 mounting hole positions and remove the enclosure from the surface. 
 
3. Choose appropriate fixings for the surface that the enclosure is being mounted to. Note 
that unless UFO are installing the unit then we do not supply fixings. This is due to the 
large variance of surface types the enclosure may be mounted to.  
 
4. Follow the instructions for the chosen fixings and use them to secure the enclosure to 
the mounting surface.

Outside/Rear 
of enclosure

MOUNTING

 

THE

 

REMOTE

 

PSU

For remote DC enclosures (suffix 
DC) the remote PSU should be 
mounted in a suitable location 
considering the following to 
minimise voltage drop between 
PSU and enclosure: 
 
1. Distance between PSU and 
enclosure.  
2. Size (AWG) of interconnecting DC 
cable between PSU and enclosure.  
 
NOTE: Maximum distance of 10m of 
interconnecting cable based on a 
minimum cable size of 16AWG. 

Summary of Contents for IP-02





















Reviews: