background image

INTRODUCTION

IONIC

 

USER

 

GUIDE

2

Thank you for purchasing this UFO Ionic lighting system. 
 
Please read these instructions fully before performing any installation, operation or 
maintenance on the system and before connecting your Ionic lighting system to the electrical 
mains. Please keep this manual for future reference. 
 
The UFO Ionic is a fully configurable magnetic track lighting system which has been specifically 
designed for ease-of-use and many installation environments. 
 

IMPORTANT

 - The UFO Ionic extrusions and tracks are ordered cut to length from UFO and  

cannot be cut or modified on site. Any attempt to cut or modify the extrusions and tracks will 
invalidate warranty for the complete UFO Ionic installation. 
 
Ionic spotlights are available in a choice of 2700k, 3000K, and 4000K colour temperatures. These 
spot lights are dimmable locally using the dimmer controls on the fittings or globally using a 
UFO supplied dimmer/driver system. 
 
Ionic spotlights operate on a constant voltage low voltage supply. Constant current and 
constant voltage LEDs cannot be intermixed on the same driver. Please refer to the specific 
section within this manual for connection guidance. 
 

WARNING

 – The Ionic system operates on 12V DC only. Connecting these fittings to a driver with 

excessive voltage output will result in catastrophic damage to the LED devices within the 
fittings. Always check the output voltage of the driver to ensure correct output voltage prior to 
powering up the system. 
 
The Ionic system is suitable for indoor/dry areas only and must not be installed in damp or wet 
conditions. 
 
I

MPORTANT 

 
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION 
CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT, 
ITS COMPONENT PARTS AND THE HAZARDS INVOLVED. 
 
 

EXTERNAL WIRES

 

To allow for full articulation of the Ionic 
snoot, there are 2 low voltage wires 
connecting it to the fitting body. Please 
ensure these wires are not twisted around 
the neck of the snoot. Applying too much 
force to these wires could cause 
irreparable damage to the fitting.  

Summary of Contents for IONIC

















Reviews: