Uflex UC 69-I Installation And Maintenance Manual Download Page 5

HYDRAULIC CYLINDERS FOR INBOARD ENGINES

 

 

 

-  

page 5 

of 23

Installation and Maintenance Manual

TECHNICAL ASSISTANCE SERVICE

INTRODUCTION

U FLEX  S.r.l.

Via Milite  Ignoto,8A

16012 Busalla (GE)-Italy

Ph.:  +39.010.962.0239  (Italy)

Ph.: +39.010.962.0244  (abroad)

Fax:  +39.010.962.0333

Email:  [email protected]

www.uflexgroup.it

North  -  South  -  Central  America:

UFLEX

  USA

6442 Parkland  Drive

Sarasota, FL  34243

Ph.:  +1.941.351.2628

Fax:  +1.941.360.9171

Email:  [email protected]

www.uflexusa.com

This installation and maintenance manual represents an important part of the product and must be available

to  the people  in charge  of its  use and  maintenance.

The user must know the content of this manual.

UFLEX 

USA  declines all  responsibility for  possible mistakes  in  this  manual due  to printing  errors.

Apart from  the  essential  features  of  the  described  product, 

UFLEX 

USA  reserves  the  right  to make  those

modifications,  such  as  descriptions,  details  and  illustrations,  that  are  considered  to  be  suitable  for  its

improvement, or for design or sales requirements, at any moment and without being obliged to update this

publication.

ALL RIGHTS  ARE RESERVED. Publishing rights,  trademarks, part  numbers and  photographs of 

UFLEX 

USA

products  contained in  this manual  are 

UFLEX

 

USA  property.

Great  care  has  been  taken  in  collecting  and  checking  the  documentation  contained  in  this  manual  to
make it as complete and comprehensible as possible. Nothing contained in this manual can be interpreted

as warranty either expressed or implied - including, not in a restricted way, the suitability warranty  for any

special purpose.    Nothing  contained in  this manual  can be  interpreted as  a modification  or confirmation  of

the  terms of  any purchase  contract.

To  ensure the  correct product and component operation, the product must  be installed by qualified staff.

In  case  of    part  damage  or  malfunction,  please  contact  the  qualified  staff  or  our  Technical  Assistance

Service.

WARNING

WARRANTY

1.  Two  Year  Limited  Warranty.

 

UFLEX

  USA, Inc.  warrants that  all  products  manufactured  by 

UFLEX

  USA,

Inc. or 

ULTRAFLEX

  S.p.A. and sold by 

UFLEX

 USA to the retail purchaser ("Purchaser") that for two (2) years

after  the date  of manufacture  to be  free from  defects due  to material  or workmanship,  subject to  the

exclusions below.  Improper installation  AVOIDS this  warranty. Installation  should only  be attempeted  by

a  trained  and  qualified  technician.

2.  Exclusions.

  This limited  warranty does  not  cover  and  does  not extend  to any  of  the  following:

(a)

 Failure  caused by  normal wear  and tear,  climatic  conditions,  misure, neglect,  lack  of  proper

maintenance,  accident,  fire or  other casualty  damage,  racing,  overloading,  negligence,  modification,

beaching or  grounding of  vessel, collision,  impact,  towing,  acts of  war or  hostilities;

(b)

  components  not  manufactured by 

UFLEX

  USA, Inc.,  or its  affiliates;

(c)

  cost of  removal or  reinstallation of  any component  (including  components  manufactured by 

UFLEX

USA,  Inc.) or  disassembly or  reassembly of  the unit  containing the  component;

(d) 

components not  manufactured by 

UFLEX

 USA,  Inc. or 

ULTRAFLEX

   S.p.A.,  whether or  not warranted  by

the  other  manufacturer;

(e)

 any  product which  has not  been properly  installed.

Summary of Contents for UC 69-I


























Reviews: