UDOIT RFT-868-USB User Manual Download Page 2

 

 

RFT-868-USB

 

Release A - 01/09/2015 

 

Copyright 2015 Udoit Srl - All rights are reserved 

 

 

www.udoit.eu 

 

 

Device Specifications 

 

Power Supply: 5V (with USB 2.0 connection)

 

 

Dimensions ( L x W x H ): 72 x 

1

0 x 24 mm 

 

Radio Module TRX Features

1

 

 

Low Rx power consumption: 10mA.

 

 

Low Tx power consumption: 33mA @+10dBm.

 

 

Low Standby consumption: 4 µA.

 

 

FSK Modulation.

 

 

Good reception sensitivity: down to -100 dBm at 25 kb/s in FSK.

 

 

Packet handling feature with data whitening and automatic CRC generation. 

 

Incoming sync word recognition. 

 

Distance coverage: up to 20 m indoors (depending on building materials). 

 

Effective Radiated Power (ERP): 5mW. 

 

RFTide Network Features 

 

Wireless mesh network topology. 

 

Proprietary routing protocol and software application. 

 

Centrally managed network from a Control Unit. 

 

Advanced Encryption Standard (AES)  of the data. 

  

Typical Applications 

 

Wireless alarm and security systems. 

 

Wireless sensor networks. 

 

Automated Meter reading. 

 

Home and building automation. 

 

Industrial monitoring and control. 

 

Remote wireless control. 

 
 
 
 
 
 

Revision History

 

Date 

Version 

Revision 

15/09/2015 

1.0 

Initial Release 

                                                 

1

  

Refer to  SEMTECH SX1211 Transceiver datasheet  

http://www.semtech.com/images/datasheet/sx1211.pdf

 

Summary of Contents for RFT-868-USB











Reviews: