background image

4

www.udirc.com

(4) Keep away from humid environment

The drone inside is consisted of precise electronic components and mechanic 

components. Humidity or water vapor may damage electronic components and

cause accident.

(5) Safe operation

Please operate the RC drone in accordance with your physical status and flying 

skill. Fatigue, listlessness and improper operation may increase the rate of accident.

(6) Keep away from high-speed rotating parts

Please keep the drone in your sight when flying. Keep rotating parts away from 

people and ground. Otherwise, may cause serious injury and damage.

(7) Keep away from heat

(8) Operation Area

(9) Do not touch the hot motor to avoid being burnt.
(10) Please use the recommended charger only. Power off the drone before cleaning 
the RC drone. Check the USB cable, charging plug etc. regularly to ensure they can 
work well. If there is any damage, stop using it immediately till it’s fixed well.

The RC drone and transmitter are made of metal, fiber, plastic, electronic 

components etc. Keep away from heat and sunshine to avoid distortion and damage.

The drone should be controlled within max control distance. Do not fly the drone near 

tall building, high voltage cable or other place with signal interference. Otherwise, it 

may affect the flight distance and streaming video range ,even may cause signal 

interruption and the drone will be out of control, which may result in accident.

Safe Notice for Drone Battery

* Keep the battery away from child and animal.

* Discontinue charging when you notice the battery is swollen.

* Do not charge the battery once it crash or damage.

* After the crash, check the battery to ensure it can work well.

* Do not overcharge the battery.

* Do not charge the battery near the flammable materials or liquids. 

* Do not put the battery on high temperature place, store it in a proper container 

   to avoid damage or explode.

* Do not put the battery in the pocket or bag to avoid short circuit and not be 

   scratched by sharp or metallic objects.

* Do not disassemble, refit and repair the battery.

* Do not use the battery to crash or hit hard surface.

* Do not put the battery in water and keep it in dry place.

* Do not leave the battery without supervision when charging.

* Make sure that there is no short circuit of the power wire.

* Please use the recommended charger only.

* Check the charger’s wire, plug, surface regularly. Do not use any broken charger.

* If the battery is not used more than one week, maintain the drone battery with 

   about 50% power to keep its performance and working life.

Summary of Contents for SLRD40

























Reviews: