background image

MADE IN CHINA

FCC Note

This equipment has been tested and found to comply with the limits for a Class B digital 
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide 
reasonable protection against harmful interference in a residential installation. This 
equipment generates uses and can radiate radio frequency energy and, if not installed and 
used in accordance with the instructions, may cause harmful interference to radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, the 
user is encouraged to try to correct the interference by one or more of the following 
measures:

 Reorient or relocate the receiving a ntenna.

 Increase the separation between the equipment and receiver.

 Connect the equipment into an outlet on a circuit different from that to which the 

     receiver is connected.

WARNING: Changes or modifications not expressly approved by the party responsible 
                  for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions: 
(1) This device may not cause harmful interference. 
(2) This device must accept any interference received, including interference that may 
      cause undesired operation.

The equipment may generate or use radio frequency energy. Changes or modifications to 
this equipment may cause harmful interference unless the modifications are expressly 
approved in the instruction manual. Modifications not authorized by the manufacturer may 
void user’s authority to operate this device.

FCC Notice:

The device has been evaluated to meet general RF exposure requirement.
The device can be used in portable exposure condition with out restriction.

FCC Radiation Exposure Statement

Model: U59

Manufacture time: 

Manufacture address: Guangfeng Industrial Zone, Guangyi Street, Chenghai District, Shantou City, Guangdong Province, China

Manufacturer company: SHANTOU CITY CHENGHAI UDIRC TOYS CO., LTD

16

Summary of Contents for U59

















Reviews: