Udey MRL-11 Operating Manual Download Page 1

Page: 1 / 21

Udeyraj Electricals Pvt. Ltd., Mumbai 400059 / Ph: + 91 22 66916181 / http://www.udeyraj.com / [email protected]

OPERATING MANUAL

File name: RKG-UEPL-MRL-11
Revision: 01
Editor: RG
Date: 15-02-2014

WARNING

DANGER

Equipment to be used by trained personnel only

This operating manual contains instructions for the operation of a electrical tester. The

operator of this equipment must use good judgment and follow all safety precautions

noted in this guide to ensure the protection of him self and others in close proximity to the

test area. Failure to follow safety instructions could be dangerous.

Proper grounding of the tester must be done prior to connecting this tester to a power

source.

UDEYRAJ ELECTRICALS PRIVATE LIMITED

212-A, Hind Saurashtra Industrial Estate,

MRL-11

CONTACT RESISTANCE TESTER

Engineered and manufactured in India by:

UDEY

Summary of Contents for MRL-11






















Search results

Summary of Contents for MRL-11

Reviews:

Related manuals for MRL-11

Brands by name

Popular brands

Udey MRL-11, Operating Manual

Search results

Summary of Contents for MRL-11

Reviews:

Related manuals for MRL-11

Brands by name

Popular brands