background image

 

EVK-NORA-W1 - User guide 

UBX-22002764 - R02 

Product description  

Page 4 of 22 

C1-Public  

 

 

1

 

Product description 

The EVK-NORA-W10 evaluation kit provides stand-alone use of the NORA-W10 series module. 

All pins and interfaces supported on NORA-W10 series modules are conveniently accessed from the 
evaluation  board.  A  simple  USB  connection  provides  the  physical  interface  for  the  power, 
programming, and COM ports. A USB peripheral connector, reset button, and four other user buttons 
are available. 

GPIO signals are available on headers that are compatible with the Arduino® form factor. This allows 
easy  use  of  existing  Arduino  shields.  Current  sense  resistors  allow  for  measuring  current  into  the 
module and into the shield. 

This  guide  provides  setup  instructions  for  starting  development  and  describes  the  hardware 
functionality of the EVK-NORA-W10 board. 

1.1

 

Key features 

EVK-NORA-W2 provides developers with access several practical features for testing and evaluating 
the connectivity options supported in NORA-W2 series modules, including: 

 

Used for evaluation of NORA-W101 or NORA-W106 modules  

 

COM ports and debug ports over USB 

 

Full GPIO of the NORA-W1 series 

 

Buttons and status LEDs for user interaction  

 

32.768 kHz crystal 

 

USB peripheral connector 

 

Power input through USB-C or pin sockets 

 

Current measurement access points from pin headers and jumpers 

 

Figure 1: EVK-NORA-W10 evaluation board (top view)  

 

 

 

 

Summary of Contents for NORA-W10 Series























Reviews: