LISA-U2 series - System integration manual
UBX-13001118 - R27
System description
Page 47 of 183
C1-Public
1.8.1
(U)SIM application circuits
1.8.1.1
SIM cards, SIM connectors and SIM chips selection
The ISO/IEC 7816, the ETSI TS 102 221 and the ETSI TS 102 671 specifications define the physical,
electrical and functional characteristics of Universal Integrated Circuit Cards (UICC) which contain
the Subscriber Identification Module (SIM) integrated circuit that securely stores all the information
needed to identify and authenticate subscribers over the GSM network.
Removable UICC / SIM card contacts mapping is defined by ISO/IEC 7816 and ETSI TS 102 221as
follows:
•
Contact C1 = VCC (Supply)
→
Must be connected to
VSIM
•
Contact C2 = RST (Reset)
→
Must be connected to
SIM_RST
•
Contact C3 = CLK (Clock)
→
Must be connected to
SIM_CLK
•
Contact C4 = AUX1 (Auxiliary contact)
→
Must be left not connected
•
Contact C5 = GND (Ground)
→
Must be connected to
GND
•
Contact C6 = VPP (Programming supply)
→
It can be left not connected
•
Contact C7 = I/O (Data input/output)
→
Must be connected to
SIM_IO
•
Contact C8 = AUX2 (Auxiliary contact)
→
Must be left not connected
A removable SIM card can have 6 contacts (C1 = VCC, C2 = RST, C3 = CLK, C5 = GND, C6 = VPP, C7 =
I/O) or 8 contacts, providing also the auxiliary contacts C4 = AUX1 and C8 = AUX2 for USB interfaces
and other uses. Only 6 contacts are required and must be connected to the module SIM card interface
as described above, since LISA-U2 modules do not support the additional auxiliary features (contacts
C4 = AUX1 and C8 = AUX2).
Removable SIM cards are suitable for applications where SIM changing is required during the product
lifetime.
A SIM card holder can have 6 or 8 positions if a mechanical card presence detector is not provided, or
it can have 6+2 or 8+2 positions if two additional pins corresponding to the normally-open mechanical
switch integrated in the SIM connector for the mechanical card presence detection are provided:
select a SIM connector providing 6+2 or 8+2 positions if the optional SIM detection feature is required
by the custom application, otherwise a connector without an integrated mechanical presence switch
can be selected.
Solderable UICC / SIM chip contacts mapping (M2M UICC Form Factor) is defined by ETSI TS 102 671
as follows:
•
Package Pin 8 = UICC Contact C1 = VCC (Supply)
→
Must be connected to
VSIM
•
Package Pin 7 = UICC Contact C2 = RST (Reset)
→
Must be connected to
SIM_RST
•
Package Pin 6 = UICC Contact C3 = CLK (Clock)
→
Must be connected to
SIM_CLK
•
Package Pin 5 = UICC Contact C4 = AUX1 (Auxiliary contact)
→
Must be left not connected
•
Package Pin 1 = UICC Contact C5 = GND (Ground)
→
Must be connected to
GND
•
Package Pin 2 = UICC Contact C6 = VPP (
Programming supply
)
→
It can be left not connected
•
Package Pin 3 = UICC Contact C7 = I/O (Data input/output)
→
It must be connected to
SIM_IO
•
Package Pin 4 = UICC Contact C8 = AUX2 (Auxiliary contact)
→
It must be left not connected
A solderable SIM chip has 8 contacts and can also provide the auxiliary contacts C4 = AUX1 and C8 =
AUX2 for USB interfaces and other uses, but only 6 contacts are required and need to be connected
to the module SIM card interface as described above, since LISA-U2 modules do not support the
additional auxiliary features (contacts C4 = AUX1 and C8 = AUX2).
Solderable SIM chips are suitable for M2M applications where it is not required to change the SIM
once installed.
