manualshive.com logo in svg

Ublox C099-F9P, User Manual

Share
Download
Ublox C099-F9P User Manual Download Page 28

 

C099-F9P - User guide 

UBX-18063024 - R16 

Firmware update

  

Page 28 of 43 

C1-Public  

 

7

 

Firmware update 

This section shows how to update the GNSS and Wi-Fi/Bluetooth module

s’

 firmware, if required. 

The board is delivered with the  latest versions  of firmware running  on the ZED-F9P and ODIN-W2 
modules. However, newer versions may become available during the lifetime of the product.  

7.1

 

ZED-F9P firmware update 

This section shows how to update the firmware and re-enable the configuration settings required for 
C099-F9P. There are two possible serial communication channels to update ZED-F9P: the UART1 and 
USB2.0 ports.  

1.

 

To update ZED-F9P, connect to u-center via USB to the COM port identified as ZED-F9P and poll 
MON-VER to view the installed firmware: see Figure 13 for the Device Manager COM port view. To 
download new firmware, follow the sequence detailed below. 

 

Figure 26: MON-VER poll response for a ZED-F9P 

2.

 

To begin updating the firmware, select 

Tools

 > 

Firmware Update

…

 

 

Figure 30: Selecting u-center Firmware Update mode 

The following 

Firmware image

 update window appears: 

Summary of Contents for C099-F9P












































Reviews:

No comments

Brands by name

Popular brands

Load more brands