manualshive.com logo in svg

Ubee DDC2700, Subscriber User Manual

Share
Download
Ubee DDC2700 Subscriber User Manual Download Page 72

4.4.5   VPN - L2TP / PPTP

Ubee Interactive

68

DDW2600 Wireless & DDC2700 Commercial Cable Modem/Router Subscriber User Guide • May, 2010

4.4.5

VPN - L2TP / PPTP

The 

L2TP / PPTP

 option allows you to configure the 

L2TP / PPTP

 parameters if this 

VPN mode is enabled. Layer 2 Tunneling Protocol (L2TP) is a tunneling protocol used 
to support virtual private networks (VPNs). PPTP (Point-to-Point Tunneling Protocol) is 
a Microsoft proprietary protocol to tunnel PPP frames, which is very similar to L2TP.

1. Access the web interface. Refer to 

page 14

, if needed.

2. Click the 

VPN 

link from the top of the screen.

3. Click 

L2TP / PPTP 

from the left side of the screen. The 

L2TP / PPTP 

fields are 

explained following this screen example.

Label

Description

PPP Address Range
Start / End

Select the specific IP range to be used for the VPN tunnels.

MPPE Encryption

Select Disabled or Enabled to enable MPPE Encryption. MPPE 
uses the RSA RC4 encryption algorithm.

Apply

Click to save the above configuration.

Username / Password / 
Confirm

Enter a Username and a Password required by that user to 
access the VPN. Reenter the password in the Confirm Password 
field.

User List

All added users are displayed.

L2TP Preshared 
Phrase

Enter a Preshared Phrase.

Apply

Click to save the configuration.

Summary of Contents for DDC2700


























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands