UBC Frost Stream Freeze Operating Instructions Manual Download Page 21

20  

  

Dispose of the equipment properly in accordance with applicable national 
disposal regulations and the regulations of your local disposal partner. 

Devices cannot be disposed of together with household waste. 

 

11. Possible malfunctions and 

recommendations for them elimination  

 

The equipment has been thoroughly tested for performance and safety. 

However, in the event of a malfunction, check the following: 

 

Is the power cord plugged into the outlet? 

 

Presence of voltage in the outlet. 

 

If the temperature is too high: 

 

Does the thermostat position correspond to the required temperature? 

 

Were the covers open and for how long? 

 

Was warm product stored/loaded? 

 

Were there power outages? 

If the malfunction is not related to any of the above reasons, contact the service 
department and report the type of malfunction. 

 
 

 

Notification 

 

 

Danger of electric shock and ignition of flammable gases. 

Untrained and unauthorized personnel may not perform any work on 

the electrical system and cooling system. 

 

 

Summary of Contents for Frost Stream Freeze
























Reviews: