revised 09/15
SMoG-HoG
®
SHn Series Models
2
SMOG-HOG NOMENCLATURE
Smog-Hog electronic air cleaners are available in a
variety of configurations and sizes. codes shown below
identify characteristics which might be built into a given
unit. the model number completely identifies the design
and can be found on the unit nameplate. For example,
a model designated SHn-10-H could be defined
according to descriptions listed below (see bold):
SHN
- SMoG-HoG n-Series
10
- airflow in 100s of cfM (i.e., 10 @ 1,000 cfM, etc.)
H
- High static pressure blower*
HH
- Higher static pressure
XB
- Without blower*
T
- tee-shaped unit (SHn-50 only)
M
- Double pass models*
*not available on SHn-50 models
Models SHN-10, SHN-20, SHN-40 & SHN-50
this type of Smog-Hog is a self-contained, two-stage,
Penney-type, electrostatic precipitator complete with
fully-interlocked, energy-limiting, high voltage power
supply, mechanical prefilter, ionizer, collection cell,
afterfilter, blower assembly, indicator light, interlock
switch and push-to-test buttons. Models available
include:
SHn-10 SHn-40
SHn-20 SHn-50-t
Models SHN-10-XB, SHN-20-XB, SHN-40-XB
this type of Smog-Hog is a self-contained, two-stage,
Penney-type, electrostatic precipitator complete with
fully-interlocked, energy-limiting, high voltage power
supply, mechanical prefilter, ionizer, collection cell,
afterfilter, indicator light, interlock switch and push-to-
test buttons. XB units are designed for use in a ducted
application where a blower is included in the existing
ventilation system. Models available include:
SHn-10-XB
SHn-20-XB
SHn-40-XB
SHN Series Voltages Available
Voltage Phase HZ Voltage Phase HZ
115
1
60
230
3
60
115
1
50
400
3
50
208
3
60
460
3
60
220
3
50
575
3
60
1. INSPECTION NOTE
upon receipt of your unit, check for any shipping
damage. a damaged carton indicates that the
equipment may have received rough handling during
shipping that may have caused internal damage. notify
your delivery carrier and enter a claim if any damage is
found.
2. INSTALLATION PLANNING
A. Unducted or Area Capture.
consideration should
be given to the placement of the precipitator to
maximize its effectiveness. The number of units
required to clean the air will depend on the layout of
the room and the concentration of pollutants.
Because it is necessary to develop proper airflow
patterns, the placement and number of precipitators
should be as suggested by uaS or your local
representative.
B. Ducted or Source Capture.
When your Smog-Hog
is used as a ducted source collector, the enclosure
or pick-up hood design is important for adequate
capture of contaminants. Drive pulleys and belts
have been selected to provide proper airflow at the
design static pressure specified. Pulleys and belts
should not be replaced without first contacting uaS
customer Service at 1-800-252-4647.
Do not operate this equipment in the presence of
combustible vapors or gases.
C. Access Clearance.
allow at least 36” (914mm) door
swing and access clearance on the door side of the
unit. All models require 18” (457mm) clearance from
the electrical junction box on top of the unit to any
overhead obstruction to allow adequate access.
3. INSTALLATION
carefully remove the unit from the shipping container,
inspecting for shipping damage. for ease of installation,
open access door and remove the cell, ionizer and
filters from the cabinet.
ceiling mounted units are suspended by means of
1⁄2” threaded rods run through weld nuts in the top
corners of the units. (refer to page 3 and 4 for weld
nut locations on all but XB models.) additional support
should be used for auxiliary equipment or ducting.
reinstall the components removed earlier to facilitate
the mounting of the unit.
A. Unit Mounting.
Models SHn-10 and SHn-20 are
designed for suspended mounting. units can be
provided with eyebolts for chain hanging, but the
length of chain should be kept level. the preferred
method of hanging is by threaded rods through
the top of the cabinet. if chain is used, it should
be of the welded link type, with a 2,000 lb. (8900
n.) test strength or better. “S” hooks used for
connections should be closed. the chain should
be hung vertically. if any angle is introduced, the
chain and fasteners should be sized to handle the
added tension. Models SHn-40 and SHn-50 may be
suspended by rods but are not approved for chain
hanging.
!
CAUTION
Summary of Contents for CLARCOR Smog-Hog SHN-10
Page 24: ...Revised 09 15 SMOG HOG SHN Series Models 20 SHN 10 20 XB SHN 10 20 APPENDIX B WIRING DIAGRAMS ...
Page 25: ...Revised 09 15 SMOG HOG SHN Series Models 21 SHN 40 SHN 10 20 M WIRING DIAGRAMS ...
Page 26: ...Revised 09 15 SMOG HOG SHN Series Models 22 SHN 40 M SHN 40 XB WIRING DIAGRAMS ...
Page 27: ...Revised 09 15 SMOG HOG SHN Series Models 23 SHN 50 T WIRING DIAGRAMS ...
