manualshive.com logo in svg

U.S. Boiler Company PV8H7, Installation, Operating And Service Instructions

Share
Download
U.S. Boiler Company PV8H7 Installation, Operating And Service Instructions Download Page 2

2

USA BOILERS

A.  Current Edition of American National Standard ANSI/NFPA 31, “Installation of Oil 

  Burning Equipment”, for recommended installation practices.

B.  Current Edition of American National Standard ANSI/NFPA 211, “Chimneys, Fireplaces,  

  Vents, and Solid Fuel Burning Appliances”, For Venting requirements.

C.  Current Edition of American Society of Mechanical Engineers ASME CSD-1, “Controls and  

  Safety Devices for Automatically Fired Boilers”, for assembly and operations of controls  

  and safety devices.

D.  All wiring on boilers installed in the USA shall be made in accordance with the National  

  Electrical  Code and/or Local Regulations. 

CAUTION

Indicates a potentially hazardous situation which, 

if not avoided, may result in moderate or minor 

injury or property damage.

WARNING

Indicates a potentially hazardous situation which, 

if not avoided, could result in death, serious injury 

or substantial property damage.

IMPORTANT  INFORMATION - READ CAREFULLY

    

The following terms are used throughout this manual to bring attention to the presence of 

hazards of various risk levels, or to important information concerning product life.

All boilers must be installed in accordance with National, State and Local Plumbing, Heating 

and Electrical Codes and the regulations of the serving utilities.  These Codes and Regulations 

may differ from this instruction manual.  Authorities having jurisdiction should be consulted 

before installations are made.

In all cases, reference should be made to the following Standards:

CANADIAN BOILERS

A.  Current Edition of Canadian Standards Association CSA B139, “Installation Code for Oil  

  Burning Equipment", for recommended Installation Practices.

B.  All wiring on boilers installed in Canada shall be made in accordance with the Canadian  

  Electrical Code and/or Local Regulations.

DANGER

Indicates an imminently hazardous situation 

which, if not avoided, will result in death, serious 

injury or substantial property damage.

NOTICE

Indicates special instructions on installation, 

operation, or maintenance which are important 

but not related to personal injury hazards.

NOTICE

This boiler has a limited warranty, a copy of which is included with this boiler.

The warranty for this boiler is valid only if the boiler has been installed, maintained and operated in 

accordance with these instructions.
Surface rust on cast iron sections may be attributed to the manufacturing process as well as condensation 

during storage.  Surface rust is normal and does not affect the performance or longevity of a boiler.

Summary of Contents for PV8H7

































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands