background image

U.S. BLINDSTITCH MACHINE CO.

IS A DIVISION OF NEW YORK SEWING MACHINE ATTACHMENT CORP.

2011-15 85th Street, North Bergen, NJ 07047 

Web: www.usblindstitch.com

Tel: 201-809-2009 • 1-800-225-2852 • FAX: 201-861-9201 • e-mail: [email protected]

2

A Machine is Only as Good as its NEEDLE!

Don’t Take Chance – Avoid Trouble

T

op quality sewing demands top quality machines equipped with top quali-

ty needles to achieve perfect results.

P

eak efficiency in today’s high-speed sewing of synthetics, and wash and

wear fabrics is accomplished only with needles of superior quality and perform-
ance.

I

mitations or substitutes are a costly compromise.  Pennies saved on infe-

rior needles only prove to be expensive dollars in the long run.

T

he quality of U.S. Needles is, in fact, a matter of world-wide recognition

and cannot be duplicated.  The confidence of our customers in U.S. Needles is
the knowledge that quality is always and has been foremost in our products.

F

or durability and freedom from breakage, U.S. Needles are unequalled.

Their uniform construction, carefully controlled finish and curvature assure 
efficient, economical stitching.

BE SURE TO USE ONLY

GENUINE U.S. NEEDLES

Look for this Label

on all parts

The same precision construction and working 
perfection exists in all U.S. Machine Parts.

BE SURE TO GET U.S. – ACCEPT NO SUBSTITUTE

GENUINE

U.S. NEEDLES

U.S. BLINDSTITCH

MACHINE CO.

2011-15 85th Street

North Bergen, NJ 07047

1-800-225-2852

TEL: 201-809-2009
FAX: 201-861-9201

From 

the 

library 

of: 

Diamond 

Needle 

Corp

Summary of Contents for 1118 Series


















Reviews: