background image

U-Line Drawer Alignment

6

Checking Drawer Alignment

The unit’s drawers are aligned at the factory before shipment. 
However, their alignment could have been disturbed during 
shipment or during overlay panel installation. Check each drawer 
to confirm that it is aligned:

Side-to-Side

 — When viewed from the top, the drawer front 

should be square with the sides of the cabinet.

Front-to-Back

 — When viewed from the side, the drawer 

front should be straight with the cabinet’s sides, not cocked 
forward or back.

Top-to-Bottom

 — When viewed from the front, the drawer 

should be level horizontally.

Adjusting Drawer Alignment

WARNING

SHOCK HAZARD — The unit must be unplugged from 
the wall outlet during drawer removal, adjustment and 
re-installation.

Drawer Removal

1. Confirm that the unit is 

unplugged from wall outlet.

2. Unplug the drawer’s connection 

wiring (top drawer only).

3. Remove the mounting screws. 

4. Pull the drawer completely out 

of the unit.

CAUTION

Use care when handling the drawer. Drawer edges, drawer 
rail and the unit’s slide may be sharp.

IMPORTANT

IMPORTANT

Drawer adjustments are made by moving the slide that carries the 
drawer’s rail. Minor adjustments may be made by loosening one of 
the slide’s mounting screws, adjusting the slide and retightening the 
screw. Severe adjustments may be made by removing the slides’ 
mounting screws, drilling new mounting holes and remounting the 
slide.

Side-to-Side Adjustment

The drawer will need a Side-to-
Side Adjustment if, when viewed 
from the top, the drawer front is 
not square with the sides of the 
cabinet. This is caused by one of 
the slides being mounted too far 
forward on the unit’s liner.

Minor Adjustment:

Note: 

The mounting holes on the 

slide are slightly larger than the 

screws’ diameter. 

1. Loosen the slide’s mounting 

screws.

2. Push the slide backward.

3. Retighten the screws. 

Severe Adjustment:

Note: 

 The slides have extra 

mounting holes that may be used.

1. Remove the slide’s mounting 

screws.

2. Reposition the slide so it is the 

same distance from the front 
of the liner as the other slide. 
Measure to confirm.

3. Mark new drilling holes using 

different sets of mounting holes on the slide.

Note: 

Front location holes are shown. Corresponding rear holes 

will also need to be marked. 

4. Drill all the new holes with a #30 drill bit.

5. Remount the slide.

Front-to-Back Adjustment

The drawer will need a Front-to-
Back Adjustment if, when viewed 
from the side, the drawer front is 
cocked forward or back. This is 
caused by the front slide 
mountings not being level with 
the rear slide mountings.

7 Standard Drawers

Aligned

Side-to-Side

Aligned
Front-to-Back

Aligned

Top-to-Bottom

Mounting

Screw

Top View of Unit

Not Aligned Side-to-Side

Push Slide

Backward

Loosen

Mounting Screws

Mark and Drill New

Mounting Holes

Push Slide

Backward

Not Aligned Front-to-Back

Side View of Unit

Summary of Contents for WINE CAPTAIN 2275DWRCOL


















Reviews: