background image

QUICK START GUIDE

8

u-line.com

Control Quick Guide

Actual Display:

First Use

All U-Line controls are preset at the factory. Initial startup 
requires no adjustments. 

NOTICE

U-Line recommends discarding the ice produced 
during the first two to three hours of operation 
to avoid possible dirt or scale that may dislodge 
from the water line.

When plugged in, the unit will begin operating under the 
factory default setting. Follow the on screen prompt for 
language selection and temperature units.

To turn the unit off, press   and hold for 5 seconds and 
release. The display will show a countdown to switching the 
unit off. 

To power your unit on, simply press  . The unit will 
immediately switch on. 

Ice

ICE CUBE THICKNESS ADJUSTMENT

NOTICE

Ice thickness adjustment should only be made 
one increment at a time. Allow ice maker 
production to stabilize for 24 hours before 
rechecking ice thickness.

Remove all ice from the storage bin.

Ice cubes in any given batch will vary, so it is necessary 
to choose cubes from the sample area for comparison 
when making adjustments.

The ice cube thickness is factory set for best overall 
performance. The factory setting “0” is designed to 
maintain an ice bridge of approximately 1/16" to 1/8" 
(1.6 mm to 3.2 mm) under normal conditions, resulting in 
a dimple of approximately 1/4" to 1/2" (6.4 mm to 

Up

Zone Toggle

Select

Down

U-Select Lighting

Power

ICE PRODUCTION

Control Function Guide:

FUNCTION

COMMAND

DISPLAY/OPTIONS

OFF

Press 

 and hold 

Display will count down from 5 to off.

ON

Press  

and 

release 

Unit 

will come on immediately.

Adjust lighting

Press 

 to adjust lighting 

Press 

 to set low, medium or high. 

Customer menu

Press 

 and hold for 5 seconds 

Press 

 to scroll through menu. 

Service menu

Press 

 and hold for 5 seconds

Press 

 to scroll through menu.

or

or

or

or

Summary of Contents for U-3018CLRS-00A















Reviews: