background image

PAGE 5 OF 18 

0421 IH-9179

OPERATION

CONTROLS

24.5

Up 

Button

Down 

Button

Setting 

Button

Display

Four Preset  

Position Buttons

USB Charger

NOTE: The desk must be initialized prior to  
first use.

•  To initialize, press and hold the down button on the 

handset until the desk reaches its lowest height, 

slightly raises and stops. 

•  Release the down button. The desk is now ready to use. 

NOTE: The desk may need to be reset from time 
to time to work properly. Unplug the power cord 
for 20 seconds, plug back in and follow the 
initialization process to reset desk. 

CAUTION! Make sure there are no obstacles in 

the desk's height adjustment path, and make 
sure the desk is not touching any walls. 

CAUTION! Make sure all cords are at the 
appropriate length to accommodate changes  

in height. 

HEIGHT ADJUSTMENT

•  Press the up button to raise the desktop. 

•  Press the down button to lower the desktop.

•  Release button to stop movement. 

CAUTION! To avoid overheating, do not move 

the desk up and down continuously for over 
two minutes within any 20 minute period. If the 
heater overheats, 

OH

 will be displayed on the 

handset. Stop using the desk for 20 minutes 
and let it cool down.

PROGRAMMING PRESET HEIGHT

•  Use up and down buttons to move desk to the 

desired position. 

•  Press and hold the setting button and one of the four 

preset position buttons simultaneously. 

•  The handset will display 

1CF

2CF

3CF

 and 

4CF

 for 

each preset when complete. 

•  Up to four presets can be programmed. 

PROGRAMMING HEIGHT LIMITS

NOTE: Desk is equipped with a height limit function. 

This function allows upper and lower height limits 
to be programmed. This can be used to prevent 
collisions with objects above and below the desk, 
such as file pedestals and overhead cabinets. 

•  Use up and down buttons to move desk to the 

desired upper height limit. Press and hold the setting 

button and up button simultaneously. The upper 

limit is set when 

HI

 is displayed. To cancel, press the 

same buttons again. The upper limit is cancelled 

when 

HCL

 is displayed.

•  Repeat the process to set the lower limit. The lower 

limit is set when 

LO

 is displayed. The lower limit is 

cancelled when 

LCL

 is displayed.

•  Always program height limits before programming 

preset heights.

SWITCHING BETWEEN INCHES AND CENTIMETERS

•  Press the setting button for seven seconds until 

SET

 

is displayed, and then press the first preset position 

button. The default unit of measurement will be 

displayed. Press the up and down button to change 

between inches and centimeters.

PROGRAMMING ANTI-COLLISION SENSITIVITY

NOTE: Desk is equipped with a gyroscope with 
an anti-collision feature. This feature allows for 
various levels of sensitivity to prevent collisions 
with objects above or below the desk.

•  Press and hold the setting button for seven seconds 

until 

SET

 is displayed, and then press the third preset 

position button to enter the sensitivity setting mode.

Summary of Contents for H-9179



















Reviews: