background image

PAGE 2 OF 9 

1121 IH-2708

OIL

Check the oil level every six months. The oil capacity is 

about 0.3L. Restore the fluid level in the reservoir to 5mm 

below the top; this must be done with the forks in the 

lowered position.

Use the hydraulic oil ISO VG 32 or equivalent.  

Oil viscosity should be 30cSt at 104° (40ºC).

HOW TO EXPEL AIR FROM THE PUMP UNIT

Air may enter the unit over time or when the seals are 

replaced. To expel the air, lift the control lever to the 

LOWER position and pump the handle up and down 
several times.

DAILY CHECK AND MAINTENANCE

Daily checks of the pallet truck can limit wear and tear 

on the unit. Pay special attention to the wheels, axles, 

handle, forks and lift and lower controls.

LUBRICATION

Use motor oil or grease to lubricate all movable parts. 

MAINTENANCE

SAFETY

For safe operation, please read all warning signs and 

instructions here and on the pallet truck prior to use.

1.  Do not operate the pallet truck unless you are familiar 

with it and have been trained and authorized to do so.

2.  Do not use the truck on sloping ground.

3.  Never place any part of your body in the lifting 

mechanism or under the forks or load. Do not carry 

passengers.

4.  Operators should wear gloves and safety shoes.

5.  Do not handle unstable or loosely stacked loads.

6.  Do not overload the truck.

7.  Always center loads on the forks, not at the end of the 

forks. (See Figure 2)

8.  The capacity of the truck assumes an evenly 

distributed load with the center of the load being at 

the halfway point of the length of the forks.  

(See Figure 2)

9.  Make sure that length of the forks matches the length 

of the pallet load. (See Figure 2)

10.  Lower the forks to lowest height when the truck is not 

being used.

Figure 2

A

B

Summary of Contents for H-8921










Reviews: