manualshive.com logo in svg

U-Line Echelon CLRCO2175S41, Installation Manual

Share
Download
U-Line Echelon CLRCO2175S41 Installation Manual Download Page 21

03/2008

21

www.U-LineService.com

CLR2160/CLRCO2175 Ice Makers

2. If the ice maker is not level, adjust the feet on the 

corners of the unit as necessary (see 

Figure 50

).

3. Check the levelness after each adjustment and repeat 

the previous steps until the unit is level. Go on to 

9 Install the Unit

.

Installation Tip

If the room floor is higher than the floor in the cut-out 
opening, adjust the rear feet to achieve a total unit rear 
height of 1/8" less than the opening’s rear height. Shorten 
the unit height in the front by adjusting the front feet. 
This allows the unit to be gently tipped into the opening. 
Readjust the front feet to level the unit after it is correctly 
positioned in the opening.

Installation of the CLR2160

1. Open the water supply valve in the main water source.

2. Plug in the power cord.

3. Open the door and press the POWER icon (see 

Figure 

53

, 

1

) (

Page

 

23

) on the display panel until OFF is 

displayed.

Note: 

If the unit is NOT turned 

OFF

, water will 

immediately start flowing into the unit when it is first 
plugged into the electrical outlet.

4. Gently push the unit into position. Be careful not to 

kink the drain or water supply line or entangle the 
electrical cord. 

5. Re-check the leveling, from front to back and side to 

side. Make any necessary adjustments. The unit’s top 
surface should be approximately 1/8" below the 
countertop.

Test the drain system by pouring one gallon of water into 
the ice bin. The water should drain freely and there should 
be no leakage.

Installation of the CLRCO2175

1. Open the water supply valve in the main water source.

2. Plug in the power cord.

3. Open the door and press the POWER icon (see 

Figure 

53

,

 1

) (

Page

 

23

) on the display until OFF is displayed.

Note: If the unit is NOT turned 

OFF

, water will 

immediately start flowing into the unit when it is first 
plugged into the electrical outlet.

4. Gently push the unit into position. Be careful not to 

kink the drain or water supply line or entangle the 
electrical cord. 

5. Re-check the leveling, from front to back and side to 

side. Make any necessary adjustments. The unit’s top 
surface should be approximately 1/8" below the 
countertop.

6. Test the drain system by pouring one gallon of water 

into the ice bin. The water should drain freely and there 
should be no leakage.

7. Remove the tape from the glass shelves and wipe out 

the inside of the unit with a clean, water-dampened 
cloth.

Turn Foot to Adjust

Figure 50

9 Install the Unit

Summary of Contents for Echelon CLRCO2175S41

























Reviews:

No comments

Brands by name

Popular brands

Load more brands