U-Line 2000 SERIES Install Manual Download Page 13

U-Line Grill Overlay Installation

11

Grille Overlay

Your models grille is designed to accept a wood grille over-
lay. An overlay may be used to compliment a door overlay 
and provides a seamless look for your surrounding decor. 
Follow the instructions below to prepare and install your 
grille overlay. Be sure to read over this chapter completely 
before beginning.

Preparation

WARNING

The grille overlay MUST have venting as shown in the 
drawing below. Failure to have proper venting can 
result in damage to your model.

WARNING

The grille overlay may only be installed on indoor units. 

1. Prepare your overlay using the dimensions provided in the 

figure on page 

12

 for 24 inch models and page 

13

 for 15 inch 

models. If using a hook and loop style mount, drill hole A will 
not be used.

2. If desired, stain and finish your grille to match your surrounding 

decor. Follow the stain manufacturers instructions to apply stain 
to your overlay.

Installation

IMPORTANT

IMPORTANT

The wood overlay grille must be installed in such a 
manner that the grille assembly can still be removed from 
the unit.

Screw Mount (Recommended)

1. Remove the grille from your unit by removing the two 

mounting screws. See below.

2. Lay the back of your grille overlay onto the front of the grille. 

Make certain the screw holes and vents are aligned. 

3. Slide each of the screws removed in step 1 through the grille 

overlay and grille. 

4. Mount your new overlay onto your unit by screwing the overlay 

back onto the base of your unit. 

Hook and Loop Fastener Mount

You may also mount your overlay to your grille using hook and 
loop type fasteners. U-Line recommends using 3M® Dual lock® 
fasteners. To mount your overlay using a hook and loop fastener 
follow the instructions below. 

1. Read the instructions provided with your hook and loop 

fastener carefully.

2. Apply hook and loop fastener system to the back of the overlay 

and front of the grille. Use the shaded areas in the diagram 
below for application location.

3. Carefully align the wood overlay with the grille and press into 

position. 

10 Wood Grille Overlay 

Remove Screw

Remove Screw

Back

Front

Wood Overlay

Grille

24 Inch Models

Application

Area

Back

Front

Wood Overlay

Grille

15 Inch Models

Application

Area

Summary of Contents for 2000 SERIES





















Reviews: