U-Line 124BEV User Manual & Service Manual Download | Manualshive

Page: 48 / 69

background image

USER GUIDE

R-600A Specifications 1

u-line.com

SAFETY • INSTALLATION & INTEGRATION • OPERATING INSTRUCTIONS • MAINTENANCE •

SERVICE

R-600A Specifications

For R-600a refrigerant service tips and more videos, go
to:

www.u-line.com/videos

.

WARNING

!

Flammability warnings for a pure-iso-butane
refrigerant.

Technician must observe all federal, state and local laws regarding refrigerants.

Gloves and Eye Protection must be used.

R-600a is considered non-toxic, but is flammable
when mixed with air.

Keep a dry powder type fire extinguisher in the
work area.

R-600a is heavier than air, do not allow any
leakage/migration to low areas such as
basements and stairs.

Never use a torch on a fully charged
refrigeration system.

Never substitute U-Line OEM replacement parts
or methods of construction.

R-600a must be stored and transported in
approved containers.

48

«
...
46
47
48
49
50
...
»

Summary of Contents for 124BEV






































































Reviews:

No comments

Related manuals for 124BEV

Brand: Norcool Pages: 11

Vintage Keeper 240

Brand: shanghai koolspace Pages: 20

Brand: Buoyant Pages: 15

Brand: Baumatic Pages: 32

Brand: Wine Cell'R Pages: 22

Brand: MOA Pages: 35

Brand: La Sommeliere Pages: 83

Brand: La Sommeliere Pages: 137

Brand: Web Pages: 4

Brand: Electrolux Pages: 17

Brand: Kadeka Pages: 8

Brand: Marvel Pages: 3

Brand: Rangemaster Pages: 16

Brand: Küppersbusch Pages: 15

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands