background image

Safety & Operator Manual 

 

Hydraulic Hand Saw HBH534*** 

    10984829 

EN 

28.08.2007 

the mandatory references for all work – Instruction leaflets are of an informative nature 
and contain certain instructions only concerning correct use. 

 

The hydraulic hand saw has been inspected before being shipped and are delivered in 
perfect condition. 

TYROLIT Hydrostress AG 

does not accept any liability for damage 

caused by the failure to observe the instructions and information provided in the Safety 
Manual and in the Operating Instructions.  
This applies in particular to: 

 

Damage caused by improper use and operator error. 

 

Damage caused by improperly installed third-party components. 

 

Damage caused by failure to observe safety-related information in the Safety Manual 
or shown on the warning signs fitted to the machine. 

 

Damage caused by defective or absence of maintenance work. 

 

Damage caused by cutting unauthorized material.  

 

Independently performed conversions and alterations may affect safety and are not 
permitted. 

 
 
 

Warning 

Danger of allergic reactions if skin comes into contact with hydraulic oil. 
Persons who have an allergic reaction to hydraulic oil must wear protective gloves and 
goggles when carrying out work where they come into contact with hydraulic oil. Any 
areas of the skin affected must be rinsed immediately with copious amounts of water. 
Failure to adhere to this regulation may result in allergic reactions or injuries to the eyes. 

 
 
 
 
 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for HBH534 series







































Reviews: