Package
Overview
Installation
1
2
3
4
Warning
and
Caution
■
If the product does not work properly, please contact your dealer
or the nearest service center. Never attempt to disassemble the
camera yourself. (We shall not be responsible for any problems
caused by unauthorized repair or maintenance.)
■
Keep away from liquid while in use.
■
In the use of the product, you must be strict compliance with the
electrical safety regulations of the nation and region. When the product
is mounted on wall or ceiling, the device shall be firmly fixed.
■
Do
not
use
camera
beyond
specified
voltage
range
.
■
Do not drop the camera or subject it to physical shock.
■
Avoid touching the camera lens.
■
If cleaning is necessary, please use clean cloth to wipe it gently.
If the device will not be used for a long time, please cover the lens
cap to protect the device from dirt.
■
Do not aim the camera at the sun or extra bright place.
■
Do not place the camera in extremely hot, cold (the operating
temperature shall be -30˚C~60˚C), dusty or damp locations, and do
not expose it to high electromagnetic radiation.
■
To avoid heat accumulation, good ventilation is required for
operating environment.
■
A few parts of the device shall be replaced regularly according
to their average enduring time.
Camera
Quick
start
guide
CD
Plastic
plug
×4
Drill
template
Sponge
Screwdriver
4 tapping screws
CVBS&DC
IN cables
①
Loosen
the
nut
from
the
main
element.
②
Run
the
network
cable (without
RJ 45
connector) through the
both elements. Then
crimp
the
cable
with
RJ 45
connector
.
③
Connect
the
cable
to
the
hermetic
connector
.
Then
tighten
the
nut
and
the
main
cover
.
●
Alarm Input
: Join the grounding ends of the sensor and the camera
and then connect the signal cable of the sensor to the alarm input
port (ALM-INA) of the camera.
Alarm Output
: Loosen the screws in the alarm output port. Then
insert the signal wires of the alarm output devices into the port of
OPEN and COM separately. Finally tighten the screws. Some of the
external alarm output devices need the power supply.
Alarm Connection
■
Please read this instruction carefully before using the product and keep
it for further reference.
■
All the examples and pictures used here are for reference only.
■
The contents of this manual are subject to change without notice.
2
1
3
*
If
the
PoE
switch is
used
to
power
the
camera
,
DC12V/AC24V power supply
is
not
required
.
*
AC24V
power
supply
is
not
available for
ISV-V05M023S-N/ISV-V05M024S-N/
JSV05-D02-OI01.
* Please make sure that the wall or ceiling is strong enough to
withstand 3 times the weight of the camera.
* Please install the camera in the dry environment. You'd better install
back the lower dome less than 4 hours after removing it.
* Do not directly touch the dome when installing.
* Do not remove the protection film until finishing the installation.
lock screw to remove the mounting base.
②
Attach the drill template to the place where you want to fix the
camera and then drill 4 screw holes and 1 cable hole (if you want to
route the cables through the mounting base) according to the drill
template.
①
Loosen the screws to open the lower dome and then loosen the
●
Connecting
Network
Cable
1
3
4
5
6
2
A
L
A
R
M
4 3 2 1
10
7
8
9
11
12
1
Ethernet
Connector
2
Audio Input (MIC)
3
Audio
Output (HP)
4
CVBS
Video Output
5
Alarm Input/Output
6
DC12V Power
Connector
7 Zoom-
8 Zoom+
9 Micro SD Card Slot
10 Reset
11 DC IN & CVBS Interface
12 Microphone
Se
cu
ri
ty c
ap
1--ALM-COM
2--ALM-OPEN
3--ALM-INA
4--ALM-GND
DC12V/AC24V
A
L
A
R
M
4 3 2 1
Illustra
Standard
Series
Dome
Camera
Quick
Start
Guide
V
