Network Connection
5
③
Route and connect these cables.
the ceiling or wall with screws.
Then secure the mounting base to
④
Fix the camera to the mounting base with the lock screw.
Sponge
Mounting
Base
⑤
Three-axis adjustment. Before adjustment, preview the image of the
camera on a monitor and then adjust the camera according to the
figure below to get an optimum angle.
⑥
Install the lower dome back to the camera with the screws. Please
tighten the screws for water resistance. Then remove the protection
film softly to complete the installation.
Lock
Screw
Lower
Dome
∅
6
∅
148
∅
22
88 mm
89mm
Transparent Dome Maintenance
Tips
Transparent dome is an optical element. As dirt, dust or fingerprints on the
dome will reduce the clarity of the image, please don’t touch or wipe the
cover surface directly during installation and use. Please refer to the
following cleaning tips to clean it.
*
*
If there is water or grease on the dome, please gently wipe off the water
drop or grease with a soft cloth and then use oil-free cotton cloth with the
neutral detergent to wipe it several times from the center to outward.
Finally, change the cloth to dry it.
*
If there are fingerprints on the dome, please use oil-free cotton cloth or
paper soaked with the neutral detergent to wipe it several times from
the center to outward and then dry it with a soft cloth.
If there is dust on the dome, please use a dry soft brush to gently brush it .
Hold it
and
rotate
Rotation 0°~345°
Tilt 0°~77°
Pan 0°~345°
MENU
IPC
Network Cable
Network Cable
Switch
Router
Computer
●
Access the camera through
TycoIPTool
①
Make sure that the camera and the PC are well connected to the
LAN.
②
Find the TycoIPTool from the CD and then install it in the
computer. After that, run the TycoIPTool as shown below.
③
Modify the IP address. The default IP address of this camera is
192.168.1.168. Click the information of the camera listed in the
above table to show the network information on the right hand.
Modify the IP address and gateway of the camera and make sure its
network address is in the same local network segment as that of the
computer. Please modify the IP address of your device according
to the practical situation.
About
Immediate
Refresh
Device Name
name
name
name
IPC
IPC
IPC
unknown
unknown
unknown
192.168.1.168
192.168.1.2
192.168.1.3
80
80
80
9008
9008
9008
255.255.
255.255.
255.255.
Device Type
Product Model
IP Address
Http Port
Data Port
Subnet
Modify Network Parameter
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192
.
168
.
1
. 168
255
.
255
.
255
. 0
192
.
168
.
1
. 1
Tip: Enter the administrator password, and
then modify the network parameters.
Restore IPC Default Configuration
Total Device: 3
Local IP Address:192
.
168
.
1
.
4
Subnet Mask:255
.
255
.
255
.
0
Gateway: 192
.
168
.
1
.
1
DNS
：
210
.
21
.
196
.
6
i
Mac Address
IP Address
Subnet Mask
Gateway
Modify
CE :98 :23 :75 :35 :22
192
.
168
.
1
. 168
255
.
255
.
255
. 0
192
.
168
.
1
. 1
Tip: Enter the administrator password, and
then modify the network parameters.
i
Modify Network Parameter
For example, the IP address of your computer is 192.168.1.4. So
the
IP address of the camera shall be changed to 192.168.1.X and the
gateway shall be changed to 192.168.1.1. After modification, please
enter the password of the administrator and click “Modify” button to
modify the settings.
The default password of the administrator is “
”.
admin
④
Double-click the camera listed in the IP-Tool or manually enter the
IP address in the address bar of the web browser to connect IP-CAM.
Then follow directions to download and install the plugin.
⑤
Enter the username and password in the login interface.
The default username is
admin
; the default password is
admin
.
Available Models:
ISV-V05M023S-N
ISV-V02M014S-N
ISV-V05M024S-N
ISV-V02M013S-N
ISA-V02M015S-N
ISA-V04M015S-N
ISV-V02M015S-N
ISV-V04M015S-N
